Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Pelsue 1690D
Summary of Contents for Pelsue 1690D
- Page 1 Part #120944-001 Product Manual: Model #1690D In-Line Heater IS O 9 0 0 1 Certified T.A. Pelsue Company 2500 South Tejon Street Englewood, Colorado, USA 80110 Tel. 800-525-8460 or 303-936-7432 Fax. 303-934-5581 Internet: www.pelsue.com Email: sales@pelsue.com...
- Page 2 Page 2 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015...
- Page 3 Pelsue continues the dedication that industry throughout the world. has made us pre-eminent in this field. Page 3 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015...
-
Page 4: Table Of Contents
4.0........Safety............12 4.1......Safety Alert Symbol 4.2......General Safety Information 5.0........Product Operation........14 5.1 ......Product Description & Capabilities 5.2 ......Start-Up & Operating Procedures Page 4 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... -
Page 5: General Information
EVERY T.A. PELSUE COMPANY EMPLOYEE IS ExPECTED TO COMMIT TO THIS PHILOSOPHY IN THE PERFORMANCE OF HIS OR HER DAILY TASkS. QUALITY FIRST! T.A. PELSUE COMPANY SENIOR MANAGEMENT TEAM Page 5 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... -
Page 6: Pelsue Product Warranty
In the event of failure of any components of a Pelsue product within the warranty period, service must be pre- approved by the T.A. Pelsue Company and service must be performed by the T.A. Pelsue Company Parts and Service Department in Englewood Colorado, or at the option of T.A. -
Page 7: Introduction & Product Information
2.0 - Introduction & Product Information Congratulations on your choice of a Pelsue Model #1690D In-Line Heater to compliment your confined space heating and ventilation operation. This equipment has been designed and manufactured to exceed confined space requirements and regulations in order to meet the needs of the discriminating operator for the efficient and safe operations of person- nel in a confined space. -
Page 8: Configuration & Assembly
3.0 - Configuration & Assembly Upon initial receipt of the #1690D In-Line Heater, inspect the packaging for any evidence that the product may have been damaged in shipment. While unpacking the product, inspect all of the components for damage. If damage to any of the components is discovered, alert the shipping carrier immediately of the damage to the shipment. - Page 9 3.1 Parts Diagram & List (continued) Item PArt NumBer DeSCrIPtION QuANtIty NumBer Table 3.1a: #1690D Parts List Page 9 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015...
- Page 10 POWER SWITCH TEMPERATURE SWITCH - HIGH PRESSURE SWITCH - LOW CONTROL TRANSFORMER REMOTE THERMOSTAT RECEPTACLE THERMOSTAT SELECTOR SWITCH Figure 3.2a: #1690D Ladder Diagram and Legend Page 10 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015...
-
Page 11: Wiring Diagram
GROUND STUD MAIN HOUSING 120V AC GROUND POWER CORD (16/3 CABLE) HEATER COMPARTMENT IGNITOR BURNER ELEMENT (SENSOR) HEAT EXCHANGER Figure 3.2b: #1690D Wiring Diagram Page 11 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... -
Page 12: Safety
You are responsible for the safe operation of your Pelsue #1690D In-Line Heater. You must ensure that anyone who will operate or work around the equipment be familiar with confined space ventilation procedures. This manual will take you step-by-step through the workings and capabilities of the #1690D In-Line Heater and alert you to all good safety and operating practices while using the system. -
Page 13: General Safety Information
! CAUTION ! - The user must ensure that the heater is located where it cannot fall into water inadvertently and the extension cords or plug connections do not lay in water. Page 13 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... -
Page 14: Product Operation
5.0 - Product Operation The following section will address the capabilities and the general operation of the Pelsue #1690D Construction Heater. The instructions contained within this section should be adhered to each and every time the product is used. Any person tasked with installing or operating this piece of equipment should be familiar with these procedures. -
Page 15: Start-Up & Operating Procedures
5.2 - Start-Up & Operating Procedures Prior to Operation, the #1690D In-Line Heater should be configured and prepared according to the following guide- lines. 1. Pre-Operation Inspection: It is necessary to perform a visual inspection, each time, prior to using the product. If deficiencies are found, remove the product from service and contact T.A. -
Page 16: Important Notes
Once a location is chosen: a. An appropriate Pelsue blower (i.e. 1325D) should be connected to the inlet of the heater and the combined heater blower setup should be 1.5 meters (approximately 5 feet) upwind -- where possible -- from the confined space, with the blower inlet pointed into the wind. -
Page 17: Troubleshooting
2. Flame sensor failure 2. Replace flame sensor / spark igniter unit Yellow flame 1. Dirty orifice(s) 1. Clean orifices Page 17 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... -
Page 18: Contact Information
For More Information... t.A. Pelsue Company 2500 S. tejon St. englewood, CO 80110 toll Free: 1-800-525-8460 telephone: 1-303-936-7432 Fax: 1-303-934-5581 Website: www.pelsue.com email: sales@pelsue.com Page 18 #120944-001 - Product Manual: Model #1690D In-Line Heater - Revision 12 - Date: 07-02-2015... - Page 20 T.A. Pelsue Company 2500 South Tejon Street, Englewood, Colorado, USA 80110 Toll free 800-525-8460 or 303-936-7432 Fax. 303-934-5581 I S O 9 0 0 1 C e rti fi ed Internet: www.pelsue.com Email: sales@pelsue.com...
Need help?
Do you have a question about the 1690D and is the answer not in the manual?
Questions and answers