Noise/Vibration Information; Technical Data - Bosch GWS 22-180 H Original Instructions Manual

OBJ_BUCH-777-010.book Page 19 Thursday, September 29, 2016 3:35 PM

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a =7.5 m/s , K =1.5 m/s
h
2
=4.5 m/s , K =1.5 m/s
Disk sanding: a
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.

Technical Data

Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Bosch Power Tools
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
2
,
period.
2
.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
GWS ...
3 601 ...
GWS ... 24-180
3 601 ... H83 M..
W 2400
W 1600
-1
min 8500
mm
mm
kg
kg
22-180 22-180 22-230
H JH
H81 L.. H81 M.. H82 L..
W 2200 2200
W 1500 1500
-1
min 8500 8500
mm 180 180
M 14 M 14
mm 25 25

–

–
kg 5.1 5.1
kg 5.0 5.0
/II /II
24-230 24-230 26-180
JH H JH
H84 L.. H84 M.. H55 M..
2400 2400
1600 1600
6500 6500
180 230 230
M 14 M 14 M 14
25 25 25
 
–
 
–
5.1 5.2 5.3
5.0 5.1 5.2
/II /II /II
1 609 92A 2C8 | (29.9.16)
English | 19
22-230
H JH
H82 M..
2200 2200
1500 1500
6500 6500
230 230
M 14 M 14
25 25

–

–
5.3 5.3
5.2 5.2
/II /II
26-230
JH JH
H56 M..
2600 2600
1700 1700
8500 6500
180 230
M 14 M 14
25 25
 
 
6.0 6.1
5.9 6.0
/II /II