Flo TRACER 1000 3G LTT1-3G Operating Instructions Manual

Gwr level transmitter

Hide thumbs

Table of Contents

Quick Links

Download this manual

OPERATING INSTRUCTIONS

TRACER 1000 3G

LTT1-3G

™

GWR LEVEL TRANSMITTER

(877) 356-5463

(p) 330-331-7331

(f) 330-331-7172

www.FLO-CORP.com

REVA 0918

Table of Contents

Summary of Contents for Flo TRACER 1000 3G LTT1-3G

Page 1: Operating Instructions
OPERATING INSTRUCTIONS TRACER 1000 3G LTT1-3G ™ GWR LEVEL TRANSMITTER (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 2: Safety Precautions
Safety Precautions If you are unsure of the suitability of a Tracer 1000™ for your installation, please consult your FLO-CORP representative for further information. NOTE: REMOVE ALL PACKING INSERTS BEFORE OPERATING LEVEL TRANSMITTER.
Page 3: Features And Benefits
The sensor can output the analyzed level as a continuous measurement reading through its analog output. TDR Sensors are also known as Guided Radars or Guided Wave Radars. (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 4: Specification
Response Time • FM Approvals Pending Sum of non linearity, Analog +/- 0.02% non repeatability, Electromagnetic hysteresis Compatibility Specifications are subject to change without notice. WIRING COMPARTMENT DIMENSIONS (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 5: Setup Menu
• <2 5 Applies a pre-set value to sensitivity based on selected • <10 • <20 DIELECTRIC Dielectric Constant range of material. • <40 • <80 • > 80 (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 6: Advanced Menu
Adjustable Blanking is a non-measurable zone. This can be increased to <150mm BLANKING ‘Blank’ out high level false echoes caused by mounting (6”) is not recommended (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 7 PARAMETER DESCRIPTION OPTIONS Set dielectric of interface layer. This adjusts the velocity compensation for the DK COMP 0-100 transmitted signal as it passes through the interface. Default 2.22 (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 8 Increasing Damping value if a smoother response trend is required. This 7. ADD DAMPING value is automatically set by the Tracking speed. 8. RUN UNIT Press RUN several times to commence unit operation (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 9: Measurement Reference
Primary Variable (Level 2 Distance in mm) Div. by 304.7851 Primary Variable Percentage Secondary Status Secondary Variable (Level 1 Distance in mm) Div. by 304.7851 Secondary Variable Percentage MEASUREMENT REFERENCE STATUS BIT MAPPING (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 10 Instructions for Assembling Detached Probe Handling and Mounting: (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 11 • For rotating the housing after installation see 'Rotating the Enclosure' section. When Installing the Tracer 3000 unit, use spanner or wrench ONLY at Process Fitting as indicated. (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 12: Placement Requirements
Placement Requirements Nozzle / Socket Mounting (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 13 Stand Pipe / Flanged Mounting (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 14 If a seal / gasket is used between the flange and the vessel ensure non coated / painted bolts are used to create ground reference with vessel. Gland Entry Wiring (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 16 DO NOT hold the enclosure during this procedure. Rotation beyond these strict limits can damage the internal cables Ensure Enclosure follows the spanner rotation and assembly integrity is not compromised (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 17 DO NOT hold the enclosure during this procedure. Rotation beyond these strict limits can damage the internal cables Ensure Enclosure follows the spanner rotation and assembly integrity is not compromised (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.FLO-CORP.com © 2018 FLO-CORP REVA 0918...
Page 19 A. Confirm mounting is within recommended specifications. B. Check the selected unit matches the required application specifications. For Hazardous Locations see appropriate safety instructions available at http://www.FLO-CORP.com C. Check the wiring is correct and all connections are secure. D. Apply power to the unit.