Advertisement
Quick Links
MODEL: EOCCPK Ethernet Power Over Coaxial Master/Slave Transceiver
Description:
The EOCCPK is designed to extend IP Ethernet transmission and forward power over coaxial cable to
IP POE cameras. The EOCCPK has a transmission distance up to 600m/1968ft (RG6) and is extremely
simple to use. Status LEDs indicate power and link connectivity/activity for RJ45 ports.
Features:
No PC required, plug & play design reduces the cables and power distribution cost
Transmits IP camera signals or other 10/100 Base-T Full Duplex IP devices over coaxial cable
Injects power over an existing coaxial cable to IP POE cameras
Up to 600 Meter transmission distance when using RG6 cable / 1640ft. using RG59 cable
Built-in 6KV surge protection at BNC and 4KV at RJ45 ports
SPECIFICATIONS:
MODEL
Extender Interface
Connector Type
Cable Type
Max. Transmission Distance
Ethernet Interface
Connector Type
Cable Type
Rate
Output Voltage
Control & Indicators
Color LED Indicator for Coaxial
Data Signal Strength
Yellow LED (On RJ45)
Green LED (On RJ45)
3625 Cincinnati Avenue, Rocklin CA 95765 ● 855-388-7422 ● techsupport@northernvideo.com
75-ohm RG59, RG6, or RG11 video-grade coaxial cable
600m (1968ft.) for RG6 coaxial cable / 500m (1640ft.) for RG59
1x RJ-45 with LEDs on Connector
Straight through or cross-over Cat5/Cat6 Cable, Auto MDI/MDIX
IEEE 802.3x, Auto-Detection for 10/100Base-T and full/half
IEEE 802.3af/at PSE@ RJ45 Port
Green：GOOD (Link speed > 60 Mbps)
Amber：MEDIUM (Link speed 20~60Mbps)
Red：BAD (Link speed < 20Mbps)
1
EOCCPK
1x BNC
duplex
OFF：NO LINK
Power On
Link/Act.
Advertisement
Summary of Contents for Northern EOCCPK
- Page 1 MODEL: EOCCPK Ethernet Power Over Coaxial Master/Slave Transceiver Description: The EOCCPK is designed to extend IP Ethernet transmission and forward power over coaxial cable to IP POE cameras. The EOCCPK has a transmission distance up to 600m/1968ft (RG6) and is extremely simple to use.
- Page 2 Humidity 20% to 85% RH. (non-condensing) 1. All EOCCPK are paired to the same network group by factory default, they can be installed directly with no need for pairing again. 2. The transmission system consists of one transceiver at NVR side and one transceiver that connects to IP cameras or other IP devices.
- Page 3 PANEL DESCRIPTIONS: 1. DC56V IN: Power Supply DC56V/65W (Included). 2. PoE: Ethernet Interface (10/100Mbps for full duplexer), for PoE Output to camera 3. ACT./LINK: Data Link for indication LED 4. POWER: Power On for indication LED 5. SIGNAL STRENGTH: G(Green):GOOD A(Amber):MEDIUM R(Red):BAD OFF：NO LINK...
- Page 4 ◆ Application Diagram 3: Single Camera w/ External Power Supply EoC Transmission System (No PoE) DC 56V/65W IP Camera Max 2000m (RG6) Ethernet Over Coaxial Transceiver with PoE Switch Monitor Before starting the pairing process, please check the notice below 1) If only setup one transmission system at NVR or control room side there is no need to do pairing process.
Need help?
Do you have a question about the EOCCPK and is the answer not in the manual?
Questions and answers