Related Manuals for Centrica PAN-14
Summary of Contents for Centrica PAN-14
- Page 1 Operation and maintenance manual PAN-14 Sensor installation guide Unit number 0000 Version 2 January 2018...
- Page 2 This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to two conditions: Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654...
- Page 3 For information about your disposal or collection points, call your distributer or vendor, or contact support@panpower.com. Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654...
-
Page 4: Table Of Contents
Monitoring sensor activity Uninstalling a sensor Sensor specifications Range of rated environmental conditions Certified CTs Troubleshooting Support Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654... -
Page 5: Overview
Unpacking the hardware Sensors are shipped in 3-unit packs. CTs are not included and can be bought separately. Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654... -
Page 6: Safety Precautions
This procedure must be carried out by a certified electrician. 1. Connect the PAN-14 sensor to the CT : 2. Connect the two CT’s outputs to the PAN-14 sensor using a 1.0-4.0mm (12-17 AWG) wires as follows: a. Connect the PAN-14 sensor’s terminal marked as ‘1’ to the CT’s terminal marked as ‘S1’... - Page 7 5. Finalize the PAN-14 sensor and the CT’s position on the panel: Maintain a reasonable distance between the CT and the sensor. Place the PAN-14 sensor on the side that is closer to the bridge • (to avoid RF blocking, make sure the CT is positioned between the sensor and the bridge).
-
Page 8: Registering The Installed Sensor
Do not leave the CT mounted/installed on a hot wire without being short circuited. It is possible to have both the PAN-14 sensor and the short circuiting wire connected to the CT at the same time. Registering the installed sensor See ‘Panoramic Power deployment guide’. -
Page 9: Sensor Specifications
UL94 V-0 external enclosure Operating temperature 0 – 50° C Storage temperature -20 – 65° C Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654... - Page 10 PAN-14 Sensor installation guide Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654...
-
Page 11: Range Of Rated Environmental Conditions
600A non-split rectangular (CCT-1200-600) • 1000A split (ICT-2000-1000) Troubleshooting If you encounter a problem, first try the following solutions: Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654... -
Page 12: Support
If it is not blinking it means that it is not receiving signals. Support More support can be obtained at support@panpwr.com Revision 1.3 January 2018 © 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. Registered in England & Wales No 3033654...