Advertisement
Quick Links
HTKWLAN02 11Mbps MINIPCI WLAN Card
A.
Introduction
The HTKWLAN02 Wireless Local Area Network(WLAN) MINIPCI Card enables
high-speed access without wires to network assets. This WLAN card uses the IEEE 802.11b
protocol to enable communicatio ns between the host and the other computers, using the 2.4GHz
ISM Radio Band for the communications medium. It supports the IEEE 802.11b network
specification for Direct Sequence Spread Spectrum (DSSS) signaling, providing data rates of 1, 2,
5.5, 11Mbps. The host computer uses the HTKWLAN02 WLAN card for communications in the
same way that it would use an Ethernet adapter.
B. Features
Support for 11, 5.5, 2 and 1 Megabit Per Second (Mbps) Data Rate
Supports the IEEE 802.11 Direct Sequence Specification
Driver Supports Microsoft Windows 98/SE, Me, 2000, XP
Provides Wireless Data Communication at Full Ethernet Speed
Designed to Fully Support Minipci Type 3B Defined Mechanical and Environment Stress
Conditions
C. Specifications
C. 1 General Specifications
?? Targeted Standard ... ... ... ... ... ... ... ... ... ..IEEE 802.11b
?? Data Rate... ... ... ... ... ... ... ... ... ... ... ... ... 1 Mbps DBPSK
User' s Guide
1
2 Mbps DQPSK
5.5Mbps CCK
11Mbps CCK
Advertisement
Summary of Contents for HighTek Harness Group HTKWLAN02
- Page 1 ISM Radio Band for the communications medium. It supports the IEEE 802.11b network specification for Direct Sequence Spread Spectrum (DSSS) signaling, providing data rates of 1, 2, 5.5, 11Mbps. The host computer uses the HTKWLAN02 WLAN card for communications in the same way that it would use an Ethernet adapter.
-
Page 2: Receive Specifications
?? Transmit Spectral Mask… … … … … … … ..-30dBc(Typ.) at First Side-Lobe ?? Supply Current… … … … … … … … … … … .400mA(Typ.) D. Installation Drivers D. 1 Installation of HTKWLAN01 Windows Drivers Step 1. With the HTKWLAN02 MINIPCI WLAN Card insert into the MINIPCI slot where is... - Page 3 Me, 2000 or XP. Step 2. Once your computer system has booted and to show a message that detecting a new device, in the same time insert the Disk what is HTKWLAN02’ s Driver for Windows into the CD-ROM drive. Step 3.
- Page 4 Step 4. Press “Yes” to continue installing Step 5. Press “Browse” to choose the destination that you require to install, then press “Next”...
- Page 5 Step 6. Choose “Next” Step 7. Install Shield is installing the program.
-
Page 6: Operation
Press “Finish” to complete the installing D. 2 Operation After you installed HTKWLAN02 driver completely, both the driver and the Configuration Utility are installed on your computer, it’ s icon appears in the System Tray in the bottom right corner of your computer. -
Page 7: Using The Wireless Lan Configuration Utility
HTKWLAN02 Configuration Utility Icon The color and layers are to shine behind the High-Tek(HTK) logo indicates the link status. ?? Red and one layer to shine indicating no or very poor link quality. ?? Yellow and two layers to shine indicating a usable but weak link. - Page 8 The fields in this menu provide the following information: Network Type : The HTK WLAN Interface adapter can operate in one of two types of networks, which are specified in the Network Type: field of the Configuration menu. Clicking the down arrow at the right of this field displays the available types. 1.
- Page 9 traffic, so there is no need to specify a channel. SSID: Officially, in wireless networks the network name is known as the SSID (Service Set ID entifier), and is used by Access Points and stations to identify a wireless LAN. Your HTK WLAN Interface adapter scans the available channels looking for an Access Point or another station which has specified this same SSID.
- Page 10 Number, FER-Frame Error Rate, Throughput). In order to reset or update this statistics list, press the “Reset” button”. Site Survey : By choosing the Site Survey option, you can scan all the channels to find all the access points within the range of your card. In Figure 1-3, the list includes information about the BSSID and SSID of the access point(s), the Channel, Mode (Network Type), whether or not WEP encryption is used, signal strength and Support Rate.
- Page 11 Encryption : By choosing this option, you can set 4 different WEP keys and specify which one of them to use. If you decide to use encryption, you can choose any of the available WEP keys (1 to 4) and the “Encryption Key Length”.
- Page 12 Advanced : Choosing the Advanced option, you can change advanced configuration settings, such as the Power Saving mode , Preamble Type , Fragmentation Threshold, and RTS/CTS Threshold (See Figure 1-5). Figure 1-5 shows the recommended configuration for the advanced settings. Before selecting Short Preamble, make sure that the other stations and APs are also supporting this feature.
- Page 13 About : By choosing this option, you can view basic information about the Utility such as the Driver and Application Version. And you can click the hyperlink to connect the website for technical support.
- Page 14 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 15 approved by the party responsible for compliance could void the user’ s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 16 the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and 2) The transmitter module may not be co-located with any other transmitter or antenna.
- Page 17 Ambassador in U.S.A Company: Everex Communications, Inc. Contact: Mrs. Su-Jean Chen Address: 5020 Brandin Court, Fremont, CA 94538 U.S.A. Tel: +1-510-6832000 Ext.108 Direct: +1-510-6832891 Fax: +1-510-6832893...
Need help?
Do you have a question about the HTKWLAN02 and is the answer not in the manual?
Questions and answers