110101 func. spec. 160926 Doc.No. 417106 Revision 170823 System KMP-V DanTaet System KMP-V is a leakage protection system for supply water installations. The system comprises a Kamstrup ultrasonic water meter MULTICAL 62, a leakage detection unit KMP-V and an electrically actuated cut-off valve. The valve is connected to the KMP-V via a DIN plug, and the water meter is connected via a data link to the KMP-V, which fetches flow readings from the water meter.
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Monitoring Max.Alarm If water is discharged continuously until the set limit is exceeded, a Max. Alarm is issued, and the installation is cut off. The flow above which consumption is considered a discharge is adjustable, permitting adaptation of the system to the various minimum flows of different installations.
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Operation The KMP-V system is operated from the front panel, which is equipped with six indicators and four buttons. Inside the front panel sits a buzzer which emits a short ’click’ sound on legitimate key operations, a longer ’boo’...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Operating Modes Switching between monitoring phases is done manually or automatically in one of two ways. Manual Phase Switching Manual Phase Switching is done using the front panel ’Holiday’ button. Holiday Mode (Low Phase) is indicated by ’Consumption’...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Function Description / Operating Modes When operating, the system may be in one of five different operating modes • Normal operation without disturbance • Normal operation with disturbance •...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Normal Operation ● ○ ● Status Status Status ○ ○ ○ Data Data Data ● ● ● Valve Valve Valve ○ ○ ○ Max.Alarm Max.Alarm Max.Alarm ☼...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 System Error Condition A critical system error has occurred, and the leakage protection system is inoperative. The water supply is unimpeded. The system is in immediate need of servicing.
Doc.No. 417106 Revision 170823 External Control System KMP-V features two digital inputs which are activated by shorting their terminals using e.g. a relay contact or a panel switch. The open terminals carry 12Vdc. Short circuit current is < 5mA. The functions invoked by activating the digital inputs are determined by internal jumper settings.
Doc.No. 417106 Revision 170823 Digital Outputs System KMP-V features three optoisolated digital, passive pulll-down outputs with a common reference potential (GND) in connector J6. Terminal J6.1 supplies a synthesized meter impulse from the water meter. The impulse value is selected in jumper row F positions 6-8.
Revision 170823 Liquid Sensor Option System KMP-V accepts one or two liquid sensors type LS-X after installation of interface ILS-C. The LS-X liquid sensor responds to a water aggregation touching both its electrodes, and can hence cause the control box to issue an alarm and if desired close the cut-off valve when wet.
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Liquid Sensor Interface ILS-C. The system can be extended by an ILS-C module, accomodating up to two Liquid Sensors LS-X. Continuous monitoring for: 1: Dry condition 2: Wet condition Alarm: "Liquid Sensor Wet"...
Revision 170823 Checking and Setting the Clock System KMP-V is equipped with a real-time clock governing the valve tightness check. The clock automatically selects Daylight Savings Time as appropriate. Slight inaccuracies may accumulate over time; therefore the clock may be checked and set as...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Checking and setting the Free time The duration for which the discharge monitor is suppressed after activating the ’Unlimited’ key can be set from one to eight hours from the front panel.
230Vac KMP-V MULTICAL From Utility To Consumer Supply Water Installation System KMP-V Legend: Cut-off Valvel Key Switch 230Vac Flow meter Page 20 of 26...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Socket and Gland Identification KMP-V A: 230Vac from mains B: 24Vac to MULTICAL C: LS-X Liquid Sensor, Alarm Relay D: Alarm Relay, PIR sensor E: Data Link to MULTICAL...
DanTaet a/s User Manual System KMP-V 110101 func. spec. 160926 Doc.No. 417106 Revision 170823 Electrical Installation The valve cable terminates in a DIN plug which connects to the KMP-V socket. Connection of the KMP-V to mains, external controls, communication and remote alarm systems is shown is illustrated here.
Revision 170823 Setting the Monitoring Function System KMP-V is delivered with pre-set default factory settings, but may be easily adapted to the actual installation by the relocation of jumpers on the circuit board mounted in the lid of the enclosure.