Table of Contents
Advertisement
Quick Links
Key Features
•
Pre-qualified Bluetooth 1.0B Module
•
RF output power class 2
•
FCC and ETSI approved
•
460 kb/s max data rate over UART
•
Multiple interface for different
applications
-UART for data
-PCM for voice
-USB for voice and data
2
•
I
C interface
•
Internal crystal oscillator
•
HCI firmware included
•
Multi Point Operation
•
Built-in shielding
Suggested Applications
•
Computers and peripherals
•
Handheld devices and accessories
•
Access points
Description
ROK 101 007 is a short-range module for implementing Bluetooth function-
ality into various electronic devices. The module consists of three major
parts; a baseband controller, a flash memory, and a radio that operates in the
globally available 2.4–2.5 GHz free ISM band.
Both data and voice transmission is supported by the module. Communica-
tion between the module and the host controller is carried out using a high-
speed USB interface compliant with USB Specifications 1.1 or an UART/
PCM interface. When using the USB interface, the module appears as a USB
slave device and therefore requires no PC resources.
ROK 101 007, which is compliant with Bluetooth version 1.0B, is a Class 2
Bluetooth Module (0 dBm) and is type-approved. The module supports all
Bluetooth profiles.
ROK 101 007
ROK 101 007
Bluetooth Module
Advertisement
Table of Contents
Related Manuals for Ericsson ROK 101 007
Summary of Contents for Ericsson ROK 101 007
- Page 1 PCM interface. When using the USB interface, the module appears as a USB slave device and therefore requires no PC resources. ROK 101 007, which is compliant with Bluetooth version 1.0B, is a Class 2 Bluetooth Module (0 dBm) and is type-approved. The module supports all...
- Page 2 Filter Radio Antenna Switch ASIC Filter Balun Tank PBA 313 01/2 13MHz Crystal RESET# Figure 1. Block Diagram Audio Link Manager Baseband Radio Figure 2. Actual size of the Ericsson Bluetooth Module, and also showing the HW and FW stack.
-
Page 3: Absolute Maximum Ratings
Preliminary ROK 101 007 Absolute Maximum Ratings Parameter Symbol Unit Temperature °C Storage temperature °C Operating temperature Power Supply -0.3 +5.25 -0.8 +3.6 CC_IO CC_IO Digital Inputs Input low voltage -0.5 Input high voltage +0.3 CC_IO Recommended Operating Conditions Temperature °C... - Page 4 ROK 101 007 Preliminary 5Parameter Condition Symbol Unit Average Current Consumption Average I CC_IO Standby 5.95 Shutdown - SW 2.35 µA Shutdown – HW See note 1 Page Scan Mode R0 Page Scan Enable PSM1 Page scan window: continuous Page scan interval : n/a (0s)
- Page 5 Preliminary ROK 101 007 RF Specifications Parameter Condition Symbol Unit General Frequency Range 2.402 2.480 Double Sided IF Bandwidth Ω Antenna load VSWR RX mode VSWR TX mode, see note 2 Receive Performance Sensitivity level : -70dBm, 0.1% 75kHz offset (max),...
- Page 6 Preliminary ROK 101 007 RF Specifications continued... TX_DATA: 64 logic 'Low' & 64 logic 'High' See note 4 Figure 3. Frequency Deviation SYNT_ON TX_ON PHD_OFF PHD_OFF TX carrier dri ft TX_DATA: High +f dev TX_DATA: Low -f dev TX_DATA: High t=214 µs...
- Page 7 Preliminary ROK 101 007 RF Specifications continued... C/I Blocking The blocking characteristics can be basically split into two regions: In- band and Out-of-band. Blocking is performed both on the chip and on the module level. • In-band – Filtering on chip –...
- Page 8 Preliminary ROK 101 007 Pin Description Pin Name Type Direction Description PCM_IN CMOS PCM data, see notes 7,9 PCM_OUT CMOS PCM data, see notes 7,9 PCM_SYNC CMOS In/Out Sets the PCM data sampling rate, see notes 7,9 PCM_CLK CMOS In/Out...
-
Page 9: Mechanical Specification
Preliminary ROK 101 007 Mechanical Specification 32.8 5.05 7.85 7.85 14.1 14.1 15.7 Detail A Detail A Co-planarity 0.1 mm 3.12 4.39 5.66 6.93 Pad size: 35 mil = 0.889 mm 9.47 Tolerance on placement: 0.02 mm Figure 8. Mechanical dimensions. - Page 10 Preliminary ROK 101 007 Application Block Schematics USB Application VCC_IO Bluetooth Host Module Wake_up Control Detach Figure 9. A typical USB configuration. UART and PCM Application VCC_IO VCC_IO RS232 RS 232 transceiver UART Bluetooth Module Codec Figure 10. A typical UART or PCM configuration.
-
Page 11: Functional Description
1b) Loop filter, filters the tuning regulates and filters the supply voltage of the VCO-tank. voltage. V is typically 3.3V and The ROK 101 007 is a complete 1c) RX-balun handles transformation two regulated voltages are Bluetooth module that has been from unbalanced to balanced produced, 2.8V and 2.2V... -
Page 12: Firmware (Fw)
ROK 101 007 Preliminary Bluetooth Radio Interface DH5 packets) and is then sent by security like encryption, authentica- The Bluetooth module is a class 2 using the same RF channel for the tion and key management. device with 4dBm maximum output entire packet. - Page 13 Over the air the encoding is program- capabilities of such a profile is mable to be CVSD, A-Law or µ-Law. are performed by Ericsson specific necessary to adjust to – see Specifi- HCI commands available in the FW Preferably the robust CVSD encoding cation of the Bluetooth System v1.0B...
-
Page 14: Assembly Guidelines
Pad Size Solder Paste It is recommended that the pads on The ROK 101 007 module is made The power-down sequence is similar the PCB should have a diameter of for surface mounting and the SSP to the power-up procedure but in the 0.7-0.9 mm. -
Page 15: Ordering Information
Ericsson Microelectronics' general conditions of sale, unless otherwise confirmed in writing. Specifications subject to change without notice. Microelectronics Ericsson Microelectronics AB SE-164 81 Kista-Stockholm, Sweden 1522-ROK 101 007 Rev. PA5 Telephone: +46 8 757 50 00 © Ericsson Microelectronics AB, April 2000 www.ericsson.com/microe... -
Page 16: Getting Started
Preliminary ROK 101 007 APPENDIX A Getting Started The ROK 101 007 Bluetooth module The list above show some parts that Principle schematic for is easy to use when designing a would make designing convenient. UART inter- connect Bluetooth application. However,... - Page 17 Preliminary ROK 101 007 Inquiry Host set-up via UART: • Read_Buffer_Size: Providing the The HCI command Inquiry with the There are 4 different types of HCI- host with information on buffer parameters LAP, Inquiry_Length, and packets accepted on the UART I/F.
- Page 18 • Write Connection Accept to Bluetooth System v1.0B. Further- Return Command Command parameters parameters set-up is completed when the event more, there is some Ericsson specific HCI_Create_Connection 0x0005 BD_ADDR Packet_Type Connection_Complete_Event is commands available for accessing Packet_Scan_Repetition_Mode Packet_Scan_Mode returned to both Host_A and Host_B HW registers and HW control –...
-
Page 19: Development Tools
• SDP – Service Discovery Protocol based on the Bluetooth module ROK EBDK and regarding extra daughter provides information on the board with ROK 101 007 as add-on 101 007. services available on a Bluetooth to the EBDK. device Please contact Ericsson Microelec-... -
Page 20: Bluetooth Information
Preliminary ROK 101 007 APPENDIX C Bluetooth Information Country Frequency range RF channels This part will be updated and new Europe & USA 2400-2483.5 MHz f = 2402 + k MHz k = 0..78 information will be added continu- Japan... - Page 21 Application specific Ericsson specific HCI commands contact Ericsson Microelectronics: antennas suitable for production are By using the Ericsson specific HCI expected to be a new market for command there are a number of Telephone: antenna designs.