Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Mixlinker APRUS II
- Page 1 APRUS II Operation Manual Mixlinker Networks (Shenzhen) Inc.
- Page 2 Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 3: Table Of Contents
Contents I. Introduction ------------------------------------------------------------- 01 II. Nomenclature --------------------------------------------------------- 02 III. Packing List ------------------------------------------------------------ 03 IV. Specification ---------------------------------------------------------- 03 V. Interfaces ---------------------------------------------------------------- 04 VI. Indicators -------------------------------------------------------------- 08 VII. Connections ---------------------------------------------------------- 09 VIII. Installation ----------------------------------------------------------- 10 IX. FCC Warnning --------------------------------------------------------- 12... -
Page 4: Introduction
APRUS is an advanced programmable Internet of Things adaptor for industrial equipment developed by Mixlinker. APRUS II is the second generation product of Mixlinker, and will be referred to as APRUS II. APRUS II is an intermediate adapter developed to address theneeds of traditional equipment for IoT. -
Page 5: Nomenclature
II. Nomenclature A2 - 4207 - B Power Input Product Info Mixlinker Advanced AC/DC 24V Input Programmable Remote Utility Server (APRUS II) Interfaces Communication Modules CAN,RS485-1,RS485-2 2G Communication Module GPS Modules Module with GPS... -
Page 6: Packing List
III. Packaging List APRUS II (1) GPS Antenna (1) - optional GSM Antenna (1) Micro SIM Card (1) IV. Specification Settings/Configurations Item Standard SMA Interface GPRS Antenna Interface (Female Connector) GPRS 2G Network Wireless Network (Not Supporting CDMA) Input Voltage... -
Page 7: Interfaces
V. Interfaces APRUS II (Interfaces on Top) Symbol Definition GPS Antenna Interface GSM Antenna Interface Ethernet Interface (Optional) APRUS II (Interface on Left Side) Symbol Definition Extended Interface... - Page 8 V. Interfaces APRUS II (Interfaces on Right Side Symbol Definition Micro SIM Card Slot USB Interface APRUS II, when using Micro SIM card, please insert the card“chip down and notched edge facing outward”...
- Page 9 V. Interfaces APRUS II (Interfaces on the Bottom) Note： When choosing adapters of one RS485 and one RS232, the default for 3 and 4 is RS232, and 6 and 7 is RS485 Item Indicator CAN-L CAN-L CAN-H CAN-H TX/A-1 RS232_TX1/RS485_A1...
- Page 10 V. Interfaces APRUS II (Front) GSM SVR GPS PWR Item Indicator GSM Indicator Light SVR Indicator Light GPS Indicator Light Power Indicator Light Reset Button SOS Button Note: Press SOS to trigger a “short press event”. Press and hold for 3 seconds to trigger a “long press event”.
-
Page 11: Indicators
VI. Indicators Note: During electrical initialization and self-testing on adaptors, the SVR, GPS and PWR indicators will simultaneously be on for 500ms and off for 500ms. Status Normal Abnormal Indicator 1. Upon successful logon of SIM card, 1. When SIM card is not registered indicator shall be on at the interval online, indicator shall be on at the of 3000ms, for 64ms each time. -
Page 12: Connections
POW - POW + POW + POW - POW - APRUS II Note: 1.This wiring diagram demonstrates an adaptor with a grouping of RS485 and RS232. For adaptors with two groups of RS485, please refer to the above diagram for the wiring of RS485. -
Page 13: Installation
VIII. Installation There are two methods for APRUS II installation: 1. With screws, screw size: M4.5, as shown below:... - Page 14 VIII. Installation 2. Installation with rails, the size of rail: 35mm, as shown below: Install stopper Rail Step 1： Step 2： Raise the stopper Install the adaptor onto on the adaptor. the rail. (Please secure the bottom rail groove onto the rail bottom first.) Note: 1.
-
Page 15: Fcc Warnning
Mixlinker Networks (Shenzhen) Inc. ：3/F Spring Tower, Meisheng Creative Valley, 10 Longchang Rd. Shenzhen ：0755-23740592 ：www.mixlinker.com V1.0...
Need help?
Do you have a question about the APRUS II and is the answer not in the manual?
Questions and answers