Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Alder Simple
- Page 1 User Manual...
-
Page 2: Table Of Contents
ALDER SIMPLE 1-855-999-7872 Table of Contents INTRODUCTION SYSTEM (23) Display Sounds PANEL Panel Location Exit Delay Home Screen Adjust Transmission Delay Home Screen Icons Test System Panel Panel Buttons System Info ALARM (11) USER PASSCODES (27) Intrusion Detection Master Passcode and Verbal... -
Page 3: Introduction
USER MANUAL WWW.ALDER.COM Introduction This Guide is designed for owners of the Alder Simple Security System. The guide will show system owners how to use the basic functions of the Alder Simple Panel after the system has been completely installed. -
Page 4: Panel
USER MANUAL WWW.ALDER.COM Panel PANEL LOCATION Your control panel serves as the heart of your system. Place it in a central location within 5 feet of an electrical outlet that does not have a “test/reset” button and is not controlled by a switch. - Page 5 ALDER SIMPLE 1-855-999-7872 SYSTEM STATUS Displays the status of the panel. Possible statuses include the following: “Hey, I’m ready to arm.” “I’m armed in Stay mode.” “I’m armed in Away mode.” “Hang on, your sensor is open.” “Hang on, you have multiple sensors that are open.”...
-
Page 6: Home Screen Icons
USER MANUAL WWW.ALDER.COM HOME SCREEN ICONS BATTERY BATTERY MESSAGES AC POWER FULL CHARGING CONNECTED NO CELLULAR UNREAD AC POWER BATTERY CONNECTION MESSAGE DISCONNECTED PANEL BUTTONS The panel has two LED lighted buttons to the right of the screen. The Home Button... -
Page 7: Alarm
USER MANUAL WWW.ALDER.COM Alarm INTRUSION DETECTION In order to arm your system to detect intrusions ensure the panel status field says, “Hey, I’m ready to arm.” Then arm the system in Stay or Away mode. ARM THE SYSTEM (STAY MODE) Select this mode when people will be staying inside. - Page 8 ALDER SIMPLE 1-855-999-7872 At the end of the countdown, the system will announce “System armed stay”, the panel status field will now display “I’m armed in stay mode.”, and the system will be armed. ARM THE SYSTEM (AWAY MODE) Select this mode when the house will be unoccupied. This mode will arm ALL anti-burglary sensors (doors, windows, motion sensors, glass break sensors) that have not been bypassed.
- Page 9 USER MANUAL WWW.ALDER.COM THERE ARE TWO WAYS TO BYPASS YOUR SENSORS: Method 1 Temporary Bypass All If multiple sensors are open, the system status will read “Hang on, you have multiple sensors that are open.” Use the “check status” to display a list of all sensors and their statuses. Possible statuses include Open, Closed, Active and Tampered.
- Page 10 ALDER SIMPLE 1-855-999-7872 alarm. To disarm the system in either mode, enter a 4-digit User Passcode or press “Disarm” on your Remote. You may also disarm your panel using the smartphone app. (See page for details) IN THE EVENT OF A BURGLARY ALARM...
-
Page 11: Fire Detection
USER MANUAL WWW.ALDER.COM hostage code simply enter it to disarm your panel. FIRE DETECTION Your Smoke+CO or Smoke/Heat/Freeze sensors are armed at all times by default. Smoke, Heat, or Freeze detection can be disabled in the individual Smoke/Heath/Freeze sensor settings. In order to... - Page 12 1-855-999-7872 MANUAL EMERGENCY CALLS You can notify the Central Monitoring Station of an emergency event directly from your Alder Simple Security Panel. To do so you must first press the Emergency Call Button on the right side of your panel, select the type of emergency (Medical, Police, or Fire) and verify you want to begin the call by tapping “Call”.
-
Page 13: Sensors
USER MANUAL WWW.ALDER.COM Sensors To access all settings, tap on the Settings icon in the top right corner of the Home Screen and enter your 4-digit Master Code. Only the Master Code can access Settings. ADD A SENSOR To add a sensor, go to Settings > Enter your 4-digit Master Code >... -
Page 14: Turn Voice On/Off
ALDER SIMPLE 1-855-999-7872 the row of the sensor for which you wish to adjust the chime settings > on the “Chime” row tap “ON” or “OFF” to turn the chime on or off. If the panel’s universal volume settings are set to “0”... - Page 15 USER MANUAL WWW.ALDER.COM Enter your 4-digit Master Code > Sensors > Doors > Tap “Edit” on the row of the door sensor for which you wish to change the Entry Delay > on the Entry Delay Row use “-“ and “+” to adjust the length of the entry delay.
- Page 16 ALDER SIMPLE 1-855-999-7872 status > tap “ON”. The default “Active in Stay” setting is “OFF” because in nearly all situations you will not want the motion triggering to set off your alarm while in “Stay Mode”. PET IMMUNITY Motion Sensors by default will not detect bodies under 55 pounds.
- Page 17 USER MANUAL WWW.ALDER.COM REMOTES Your Remote can be used to arm and disarm your panel from a distance or send an emergency signal. The Remote command buttons will function as long as the remote is within 100 feet of the panel. There are four buttons on the Remote: Away, Stay, Disarm, and SOS.
- Page 18 ALDER SIMPLE 1-855-999-7872 SMOKE SENSORS FIRE ALARM VERIFICATION To turn a Smoke Sensor’s Fire Alarm Verification setting ON or OFF go to Settings > Enter your 4-digit Master Code > Sensors > Smoke > Select the Smoke sensor type > Tap “Edit” on the row of the Smoke Sensor for which you wish to change the Fire Alarm Verification >...
- Page 19 USER MANUAL WWW.ALDER.COM This detector requires 3 AAA E92 batteries. Make sure to wait 20 seconds before installing the new battery to ensure a proper power- down. Insert the batteries in the compartment. Always match the plus (+) sign on the battery with the flat side of the compartment and the minus (-) sign on the battery with the spring side of the compartment.
- Page 20 ALDER SIMPLE 1-855-999-7872 CHANGE CO DETECTOR BATTERIES To change the CO Detector batteries twist the detector counterclockwise from its mounting base. Make sure to wait 20 seconds before installing the new battery to ensure a proper power- down. The CO Detector requires one CR123A battery.
- Page 21 USER MANUAL WWW.ALDER.COM near a water heater; or in a basement. TEST A FLOOD / FREEZE SENSOR To test a Flood / Freeze Sensor, go to Settings > Enter your 4-digit Master Code > Sensors > Flood > Tap Edit on the row of the sensor you wish to test >...
- Page 22 ALDER SIMPLE 1-855-999-7872 CHANGE GLASS BREAK DETECTOR BATTERIES To change the batteries simply rotate the detector in a counter- clockwise motion to remove the detector from the mounting plate. The Glass Break Detector requires two CR 123A batteries. Insert the batteries in the compartment. Always match the plus...
-
Page 23: System
USER MANUAL WWW.ALDER.COM System The system menu gives you the option to adjust the Display, Sounds, and Exit Delay Settings. You can also view System Info and Test your system. DISPLAY ADJUST SCREEN BRIGHTNESS To Adjust your screen’s brightness Tap Settings > Enter your 4-digit Master Code >... -
Page 24: Exit Delay
ALDER SIMPLE 1-855-999-7872 use “+” and “-” to adjust the panel volume. This changes the volume of voice announcements and chimes. You can also adjust the Panel Volume by using the “+” and “-” buttons in the bottom right corner of the Home screen. -
Page 25: Test System Panel
USER MANUAL WWW.ALDER.COM “+” and “-” to adjust to your desired delay. The options are 0, 15, 30, or 45 seconds. The Transmission Delay does not apply to Smoke or Flood sensors which will always send a signal immediately. If you disarm your system during the Transmission Delay, the panel screen will notify you that the signal was aborted. -
Page 26: System Info
ALDER SIMPLE 1-855-999-7872 status of “Verified”. You do not need to wait for one sensor to reach “Verified” status before triggering another. The “TEST” button will turn green if all sensors passed the test and red if there was a problem. Call Technical Support at 885 999-7872 if ALL sensors do not reach “Verified”... -
Page 27: User Passcodes
Your Verbal Password is a word or phrase that you established when you purchased your system. It is used to verify your identity when an alarm is triggered or when speaking with Alder Simple about your account. SECURE ARMING When Secure Arming is turned “On”... -
Page 28: Reset Hostage Passcode
ALDER SIMPLE 1-855-999-7872 RESET HOSTAGE PASSCODE To reset your Hostage Passcode tap Settings > Enter your 4-digit Master Code > Tap User Passcodes > Tap Reset on the Hostage Passcode row > Enter your new 4-digit Hostage code. ADD NEW USER To add a new user tap Settings >... -
Page 29: History
USER MANUAL WWW.ALDER.COM History VIEW HISTORY Tap Settings > Enter your 4-digit Master Code > Tap History. The history screen will show up to 200 of the most recent panel events with the time and date of occurrence. The 201st event will automatically erase and be replaced by the next oldest event. -
Page 30: Messages
USER MANUAL WWW.ALDER.COM Messages & Trouble Alerts MESSAGES You can view your messages by tapping the envelope on the Home Screen. The envelope will have a red circle with the number of unread messages and flash when there is an unread message. - Page 31 Legal & Warnings LIMITED WARRANTY This product is warranted against defects in material and workmanship for one (1) year. This warranty extends only to wholesale customers who buy directly from Alpheus Digital Company, LTD or through Alpheus Digital Company, LTD’s normal distribution channels. Alpheus Digital Company, LTD does not warrant this product to consumers.
- Page 32 waste equipment for recycling, please contact your local city office, or your household waste disposal service, or the shop where you purchased the product. WARNINGS Limitations of Alarm Products This product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, and other adverse events that have the potential to result in injury or loss of life;...
- Page 33 sleepers or the hearing-impaired, or overwhelmed by other sounds. Risk of Noise Induced Hearing Loss The alarm is equipped with a warning siren. Exposure to high sound levels or prolonged exposure to the warning siren can result in Noise Induced Hearing Loss (NIHL) Wireless Product Notice Radio controls provide a reliable communications link and fill an important need in portable wireless signaling;...
- Page 34 equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This devise has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules.
- Page 35 d. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modification made to this device that are not approved by Alpheus Digital Company, LTD may void the authority granted to the user by the FCC to operate this equipment.
Need help?
Do you have a question about the Simple and is the answer not in the manual?
Questions and answers
Why does my panel light up through the night with no motion?
The Alder Simple panel screen may light up at night due to the Display Timeout setting. If the timeout period has not elapsed, the screen may remain active. Additionally, system notifications, alerts, or changes in system status could cause the screen to wake up. Adjusting the Display Timeout setting in the system settings can help control this behavior.
This answer is automatically generated