Related Manuals for Fn-Link F89FTSM13-W3
Summary of Contents for Fn-Link F89FTSM13-W3
- Page 1 欧智通科技 Fn-Link F89FTSM13-W3 WiFi Single-band 1X1 802.11 b/g/n User's Manual FN-LINK TECHNOLOGY LIMITED Proprietary & Confidential Information...
-
Page 2: Table Of Contents
FN-LINK TECHNOLOGY LIMITED CONTENTS REVESION HISTORY............................... 3 1.1 MODEL NO DEFINITION............................3 INTRODUCTIONS..............................4 OVERVEIW................................4 PRODUCT FEATURES............................. 4 GENERAL SPECIFICATION............................ 5 WIFI RF SPECIFICATION..........................5 POWER CONSUMPTION..........................5 MECHANICAL SPECIFICATION..........................6 OUTLINE DRAWING............................6 PCB LAYOUT..............................6 PIN DEFINITION..............................7 APPLICATION CIRCUIT............................ 8 ENVIRONMENTAL REQUIREMENTS........................9 OPERATING &... -
Page 3: Revesion History
FN-LINK TECHNOLOGY LIMITED 0. Revision History REV NO Date Modifications Draft Rev.1.0 2015-7-9 First Released Allen Hu http://www.fn-link.com Page3/12... -
Page 4: Introductions
1. Introduction 1.1 Overview F89FTSM13-W3 is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 150 Mbps. The general hardware for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8189FTV. -
Page 5: General Specification
FN-LINK TECHNOLOGY LIMITED 2. GENERAL SPECIFICATION 2.1 WiFi RF Specifications Main Chipset RTL8189FTV Operating Frequency 2.400～2.4835GHz Standards WiFi: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, Modulation WiFi: 802.11b: CCK(11, 5.5Mbps), QPSK(2Mbps), BPSK(1Mbps), 802.11 g/n: OFDM PHY Data rates WiFi: 802.11b: 11,5.5,2,1 Mbps 802.11g: 54,48,36,24,18,12,9,6 Mbps... -
Page 6: Mechanical Specification
FN-LINK TECHNOLOGY LIMITED 3. Mechanical Specification 3.1 Outline Drawing 3.2 PCB LAYOUT (Unit: ±0.15mm) http://www.fn-link.com Page6/12... -
Page 7: Pin Definition
FN-LINK TECHNOLOGY LIMITED 3.3 PIN Assignment Pin # Name Description RF OUTPUT VBAT 3.3V Optional WL_REG_ON WL_REG_ON WL_HOST_WAKE WAKE UP SDIO_DATA_2 SDIO_D2 SDIO_DATA_3 SDIO_D3 SDIO_DATA_CMD SDIO_CMD SDIO_DATA_CLK SDIO_CLK SDIO_DATA_D0 SDIO_D0 SDIO_DATA_D1 SDIO_D1 VDIO 1.8~3.3V CLK_REQ 25~29 TCXO_IN 26MHz_IN http://www.fn-link.com Page7/12... -
Page 8: Application Circuit
FN-LINK TECHNOLOGY LIMITED 34~35 37~40 42~44 3.4 Application Circuit http://www.fn-link.com Page8/12... -
Page 9: Environmental Requirements
FN-LINK TECHNOLOGY LIMITED 4. Environmental Requirements 4.1 Operating & storage tempreture Temperature: -20°C to +70°C Operating Relative Humidity: 10-90% (non-condensing) Temperature: -40°C to +80°C (non-operating) Storage Relative Humidity: 5-90% (non-condensing) MTBF (Mean Time Between Failures) Over 150,000hours 4.2 Recommended Reflow Profile Referred to IPC/JEDEC standard. -
Page 10: Packing Information
FN-LINK TECHNOLOGY LIMITED 3. Once opened, such as when not used up within 168 hours: 1). The module must be again to remove the module moisture absorption. 2). The baking temperature: 125 ℃, 8 hours. 3.) After baking, put the right amount of desiccant to seal packages. - Page 11 The final end product must be labelled in a visible area with the following "Contains TX FCC ID: 2AATL-F89FTSM13-W3". If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of the FCC Rules.
- Page 12 The module must in the end-product be installed in such manner that the authorized antennas can be used, any change of the antenna will void the certification. EU Regulatory Conformance Hereby, we(FN-LINK TECHNOLOGY LIMITED) declared that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU Page12/12...