kenall SIMPLESEAL CDL6VL2 LED SERIES Installation Instructions

Advertisement

SIMPLESEAL
DOWNLIGHTS
CDL6VL2 LED SERIES
INSTALLATION INSTRUCTIONS
GENERAL
This instruction sheet applies for the CDL6VL2, HADL6VL2, MDL6VL2, M2DL6VL2, and TDL6VL2 Downlight.
•    D isconnect power to all circuits before wiring system. 
•    I nstall in accordance with all national, state, and local codes. 
•    B e sure to connect LED luminaire's chassis GROUND connection to a GROUNDED conductor wire.
•    R ead all product markings and labels to ensure correct installation of a system. Supplemental instructions may 
be located on the fixture, in addition to this instruction sheet, regarding orientation or mounting restrictions.
This lighting system contains sensitive electronics. Take care to avoid damage by improper handling or static 
electricity discharge (ESD). Either type of damage could render the system inoperable or cause latent failure.
I. Luminaire Mounting Procedure GRID FIXTURE
•    C ut an 8.125" diameter hole in ceiling
panel and install panel.
•    I nsert conduit or c-channel (by others) through 
mounting brackets. Bend brackets to secure. 
Lift fixture into ceiling through adjacent opening 
and position over cutout.
www. kenall.com
P: 800-4-Kenall
INSTALLATION INSTRUCTIONS

IMPORTANT SAFEGUARDS

IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
When using electrical equipment, basic safety precautions
should always be followed, including the following:
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
ORIENTATION, OR MOUNTING RESTRICTIONS.
ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
Figure 1
CDL6VL2_F-5507_110514
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIMPLESEAL CDL6VL2 LED SERIES and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for kenall SIMPLESEAL CDL6VL2 LED SERIES

  • Page 1 •    R ead all product markings and labels to ensure correct installation of a system. Supplemental instructions may  be located on the fixture, in addition to this instruction sheet, regarding orientation or mounting restrictions. This lighting system contains sensitive electronics. Take care to avoid damage by improper handling or static  electricity discharge (ESD). Either type of damage could render the system inoperable or cause latent failure. I. Luminaire Mounting Procedure GRID FIXTURE •    C ut an 8.125" diameter hole in ceiling panel and install panel. •    I nsert conduit or c-channel (by others) through  mounting brackets. Bend brackets to secure.  Lift fixture into ceiling through adjacent opening  and position over cutout. Figure 1 www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 CDL6VL2_F-5507_110514...
  • Page 2 Figure 2 II. Luminaire Mounting Procedure FLANGE FIXTURE •   I nsert conduit or c-channel (by others) through  mounting brackets. Bend brackets to secure. •   M ount fixture in ceiling so that the weight of the  fixture is supported by framing material and/or  hanger wires secured to the building structure. Figure 3 •   B ottom of diecast frame should be flush with room  side surface of ceiling panel. Adjust mounting  brackets by loosening (4) wingnuts (inside fixture)  and adjust fixture to correct height; retighten nuts. Figure 4 www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 CDL6VL2_F-5507_110514...
  • Page 3 •    C AP GRAY/ VIOLET LEADS IF DIMMER IS NOT  CONNECTED. NOTE: If using a dimmer, Kenall recommends the  Leviton  IllumaTech  IP710 series dimmer or the  ® ™ Grafik Eye GRX-TVI Control Interface for 0-10V control  and switching capability. Contact Kenall for suitability  Figure 6 of using an alternate sink-type 0-10V dimmer. •    C onnect power and test for proper operation of  luminaire. Make sure all LEDs are lit and dimming  operation works as intended (if connected). IV. Conclusion of Luminaire Mounting Procedure •   I nstall trim (shipped separately) into frame opening.  Attach trim to frame using (4) captive fasteners. www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 CDL6VL2_F-5507_110514...
  • Page 4: Customer Service

    INSTALLATION INSTRUCTIONS CUSTOMER SERVICE For technical assistance, call 1-800-4KENALL (1-800-453-6255). WARRANTY This product is warranted by Kenall to be free of defects in workmanship and materials for a period of one (1) year  from the date of the invoice. LED lamps and internal power regulation components are warranted for a period of  five (5) years from the date of the invoice against defects in materials and workmanship. The external DC power  supply carries a three year warranty from the date of the invoice. Kenall reserves the right to issue credit, repair, or replace the defective merchandise, at its discretion, upon  notification and confirmation by its local representative of the defect. Kenall also reserves the right to test and  examine the defective product if the defect is questionable and to deny the warranty herein for any product  altered, improperly installed, installed in applications for which it is not intended. This includes operation in  ambient temperatures above stated limits for any length of time. Failure by electrical surge shall not be covered  under warranty. Kenall assumes no responsibility for labor or freight costs incurred in connection with the installation, removal, or  replacement of products determined to be defective or any other consequential or incidental damages arising from  the use of the product. Kenall’s entire liability on any claim of loss or damage resulting from a defective product is  limited to the replacement price of the product. www. kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 CDL6VL2_F-5507_110514...

Table of Contents