Summary of Contents for Central Machinery Industrial 97816
Page 1
CABINET TABLE SAW LEFT TILT Model 97816 SET up ANd OpErATINg INSTruCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. ® distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011...
Never modify the plug in minor or moderate injury. any way. do not use any adapter SKU 97816 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
Always do not use the power tool if the wear eye protection. Safety equip- switch does not turn it on and off. SKU 97816 For technical questions, please call 1-800-444-3353. Page 4...
These carry important safety from those intended could result in a information. If unreadable or miss- hazardous situation. ing, contact Harbor Freight Tools for a replacement. SKU 97816 For technical questions, please call 1-800-444-3353. Page 5...
Page 6
Saw cut. Blade to cut without being forced. Before using the Table Saw, check to make sure the Saw Blade is properly mounted on the Saw Spindle. Make SKU 97816 For technical questions, please call 1-800-444-3353. Page 6...
Page 7
(walk up), and eject it toward the operator. Kickback • Never use the Fence assembly as a is a result of tool misuse and/or incor- guide when crosscutting. SKU 97816 For technical questions, please call 1-800-444-3353. Page 7...
Page 8
Keep the Table of the Table Saw clean and clear of debris. Remove Some examples of these chemicals cut-off pieces and scraps of wood from the Table before starting the Table Saw. SKU 97816 For technical questions, please call 1-800-444-3353. Page 8...
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord SKU 97816 For technical questions, please call 1-800-444-3353. Page 9...
If duST pOrT any parts are missing or broken, please (124) call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 97816 For technical questions, please call 1-800-444-3353. Page 10...
Re- and side to side. If necessary, use move this Brace before continuing shims (not included) under the cor- with assembly. The Bolts that secure ners of the Saw. SKU 97816 For technical questions, please call 1-800-444-3353. Page 11...
Wing (127) with the top of the Table (126) directly above the rear Cap Screws (128), and flush with the edge of the Table. Then, firmly tighten the Cap Screws. (See Figure E.) SKU 97816 For technical questions, please call 1-800-444-3353. Page 12...
Page 13
(See Figure H, next page.) Repeat Steps #1 through #4 above for the remaining Hand Wheel (202), Height Shaft (245), Hand Wheel Lock (201), and Handle. (See Figure H.) SKU 97816 For technical questions, please call 1-800-444-3353. Page 13...
Page 14
Use one accessory Spanner to firmly Table Insert (131 or 136). Position the tighten (turning counterclockwise) the Saw Blade at 90°. Then, raise and SKU 97816 For technical questions, please call 1-800-444-3353. Page 14...
Page 15
(See Figure K.) Slide the Splitter (311) downward with its mounting slot inserted onto the threads of the Hex Head Bolt (318). Then retighten the Hex Head Bolt. (See Figure K.) SKU 97816 For technical questions, please call 1-800-444-3353. Page 15...
(126) top. Adjust as necessary, and tighten all loose bolts before use. NOTE: If the Splitter (311) is posi- tioned to the left of the Saw Blade, alignment cannot be achieved by add- SKU 97816 For technical questions, please call 1-800-444-3353. Page 16...
Page 17
The Stops have been adjusted at the are back in alignment, tighten the Set factory. After a period of use, or after Screw securely. (See Figure Q.) moving the Table Saw from one lo- SKU 97816 For technical questions, please call 1-800-444-3353. Page 17...
Page 18
If the Saw Blade is not at 90° open out of the way of the Saw Blade. the Motor Cover (114) to expose the (See Figure A.) Geared Trunnion (247). Loosen the SKU 97816 For technical questions, please call 1-800-444-3353. Page 18...
(distance from Saw Blade to Rip Fence) by viewing on the scale indi- cator located on the right hand side of fence. Then, pull down on the Lock SKU 97816 For technical questions, please call 1-800-444-3353. Page 19...
Page 20
(408) to the desired angle of cut. Tighten Knob (418). (See Figure W.) Place the workpiece on the Table Saw and firmly against the Miter Gauge Body (408). (See Figure W.) SKU 97816 For technical questions, please call 1-800-444-3353. Page 20...
Blade. Using a dull Saw Blade will cause excessive wear on the Motor Remove the cut workpiece and debris of the Table Saw and will not produce from the Table Saw. SKU 97816 For technical questions, please call 1-800-444-3353. Page 21...
Page 22
Check and adjust as follows: be replaced only by a qualified ser- • With moderate pressure, push the vice technician. center of each V-Belt. Note the amount of deflection. Deflection SKU 97816 For technical questions, please call 1-800-444-3353. Page 22...
Push the material all the way past saw blade before releasing workpiece. Anti-kickback plates dull. Replace or sharpen anti-kickback plates. Other causes. Refer to other possible causes in “Table Saw Safety Warnings” section in this manual. SKU 97816 For technical questions, please call 1-800-444-3353. Page 23...
Page 30
Splitter Tighten Clip Supporting Arm Support Bracket Spring Pin Hex Head Bolt Pawl Cap Screw Pawl Elastic Washer Spring Flat Washer Spacer Set Screw Splitter Set Screw Hex Head Bolt SKU 97816 For technical questions, please call 1-800-444-3353. Page 30...
Page 32
Cap Screw Miter Gauge Pointer Ring (Miter) Flat Washer Flat Head Screw Elastic Washer Miter Gauge Pin Pan Head Screw Miter Gauge Body Miter Knob Pin Knob Large Washer Pin Support SKU 97816 For technical questions, please call 1-800-444-3353. Page 32...
Page 33
LIST & ASSEMBLY dIAgrAM pOWEr SWITCH ASSEMBLY SKU 97816 For technical questions, please call 1-800-444-3353. Page 33...
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 97816 For technical questions, please call 1-800-444-3353. Page 34...