1. Manuals
  2. Brands
  3. MecPower Tecway Manuals
  4. Game
  5. Happy Dog
  6. Technical specification, installation and operation manual

MecPower Tecway Happy Dog Technical Specification, Installation And Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Happy Dog Operation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Happy Dog and is the answer not in the manual?

Questions and answers

Summary of Contents for MecPower Tecway Happy Dog

  • Page 1 Happy Dog Operation Manual...

  • Page 2: Table Of Contents

    CONTENT GAME PLAY OPERATION ............2 TECHNICAL PARAMETER ............3 SETTING ..............5 ADJUSTMENT .............. 12 ............12 DJUSTMENT FOR COIN MECH ............13 OLUME DJUSTMENT ............14 AILY HECKING ............14 AILY AINTENANCE TROUBLE SHOOTING ............15 PART ASSY. DIAGRAM & PART LIST ........... 16 &...

  • Page 3: Game Play Operation

    1. GAME PLAY OPERATION Game Play Operation： 1) Insert coin, display board will show 1 that can start game. 2) Control the rod to move forward/back; left/right, stop at the figure you want to pick up. 3) Press confirm button, claw will fall down to pick up the figure. 4) After seconds, claw will raise and move to mouth of prize out, jaw opening prize will come out in the prize out mouth.

  • Page 4: Technical Parameter

    2. TECHNICAL PARAMETER Voltage：AC220V/110V（50/60HZ） Max. Current：0.55A/1.1A （Note: The proper voltage and current used accords to the nameplate at the back door of the game） Max. Power：60W Min. Power：35W Coin Size：φ21mm ~ φ30mm (diameter) 1.2mm ~ 2.5mm (thickness) Capacity of coin box：about 2300 pcs with coin sizeφ25mm*1.5mm Location required：...
  • Page 5 Spare Part List： PICTURE ITEM SPEC./MODEL LED light 12V White Micro Switch 1285 ＃ 2pcs 1396 ＃ 2pcs Manual...

  • Page 6: Setting

    3. SETTING 指拔开关组位置图 Place of Switch Main Board 主机板 SW1-SW4 Switch SW1-SW4开关组 SW1-SW4 主机板 Main Board There are four sets switches SW1, SW2, SW3, SW4, every set has eight small switches, set for ON switch open; set for OFF switch close. It need to set for the switches to change for the game.
  • Page 7 DIP SW2 on main board setting diagram Main bo ard DIP Content 1 coin/1 play 1 coin/2 play Coin 2 coins/1 play O FF 5 coins/6 play 3 s econds(must choose) 4 seconds Time for pick up figure 5 seconds O FF 6 seconds 10 seconds...
  • Page 8 motor and main board. Please pay attention for this setting item.  Time for claw move front/back; left/right： This setting is for time of claw move front/back; left/right. If setting for “10 seconds”, then the time for move is 10 seconds, after 10 seconds do not press the confirm button to get the figure, claw will fall down automatically to get the figure.
  • Page 9 Main Board DIP SW3 setting instruction:  Whether open TEST/setting： This setting is for whether open TEST/part of setting. If setting for “Open TEST”, when reset the machine will enter into TEST/part of setting condition.
  • Page 10  Whether to open the reverse position stop crane： This setting is decided for whether to open the reverse position stop crane. The machine must be set for “Not Open”, otherwise can not operate properly.  Whether save for coin information when turn off： This setting is decided when power off whether to save the coin or play times data before power off.
  • Page 11  Strong jaw to the weak claw is no delay： This setting is decided when strong jaw change to weak claw has delay or not. If setting for “No Delay”, then strong jaw change to weak claw is no delay. ...
  • Page 12 Main Board DIP SW4 Switch Setting main board DIP SW4 setting content exclude add 1 exclude add 2 exclude add 4 exclude Play time add 8 added in exclude reward mode add 16 exclude add 32 exclude add 64 exclude add 1280 The letter in bold is for factory setting ...

  • Page 13: Adjustment

    ADJUSTMENT Adjustment for coin mech Coin Adjust Chip Sample coin slot Resistance Adjust for coin Power/Signal GRAY COUNTER(+/-) Return coin rod DC+12V COIN SIGNAL WHITE BLACK GROUND COIN Signal Switch COUNTER(-/+) GRAY N.O. 精准 正常 N.C. 100ms SLOW COIN Signal Adjust Switch 50ms MEDIUM 25ms FAST Coin Mech...

  • Page 14: Volume Adjustment

    increase the sensitivity of token tolerance, that is, the range of accepting the token tolerance will be larger. Counterclockwise: decrease the sensitivity, that is, the range will be smaller and choose the token more strictly. Volume Adjustment 声音板 Sound Board 音量电位器...

  • Page 15: Daily Checking

    Daily Checking Item Content Coin Mech Check coin mech can work or not Claw Check claw can move front/back; left/right movement Claw catch Check claw can catch or not. Rod、Confirm Check rod, confirm button can work or not. button Display board Check display board can display or not.

  • Page 16: Trouble Shooting

    5. TROUBLE SHOOTING Trouble Shooting： Faulty Cause Solution No sample coin Snap the sample coin Get through for the coin Do not insert coin Sensitive is high Adjust the coin mech sensitive Coin mech damage Change coin mech Light wire blocked. Connect the light wire.

  • Page 17: Part Assy. Diagram & Part List

    6. Part Assy. Diagram & Part List Door Assy. Diagram & Part List Cabinet Assy. Diagram & Part List Supporting Frame Assy. Diagram & Part List...

  • Page 18: Claw Assy. Diagram & Part List

    Claw Assy. Diagram & Part List 6.5 Claw Assy. 2 Diagram & Part List...

  • Page 19: Cabinet Assy. Diagram & Part List

    Cabinet Assy. Diagram & Part List PC Board Assy. Diagram & Part List...

  • Page 20: Wiring Diagram

    7. WIRING DIAGRAM YL9P B ack l i m it s wi t ch M al e e nd Fe m ale end G/W1 Front li m i t sw i t ch Grey4 Grey4 B/W2 Sou nd Boa rd G/W1 G/W1 Grey1...

Table of Contents