UAV-1001191-001 2 Warnings / Disclaimers All device operational procedures must be learned on the ground. uAvionix is not liable for damages arising from the use or misuse of this product. This equipment has received a FAA transmit license for manned...
For the duration of the warranty period, uAvionix, at its sole option, will repair or replace any product which fails under normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost.
5.1 Description 5.1.1 Transponder The EchoESX is a Mode S, Level 2els transponder with support for ADS-B extended squitter. The EchoESX has a nominal power output of 250W and meets the power output requirements for Class 1. The ADS-B function meets DO-260B class B1S.
UAV-1001191-001 6.1 Markings uAvionix FCCID: 2AFFTP200S P/N UAV-1001190-001 Meets the Performance Requirements of: TSO-C112e Level 2els Class 1 and TSO-C166b Class B1S 7 Equipment Limitations 7.1 Installation 7.1.1 Modifications and Use Outside of Intended Scope This device has been designed and tested to conform to all applicable standards in the original form and when configured with the components shipped with the device.
UAV-1001191-001 devices or external antennas; such items must still be approved under existing minor modification/change processes applicable to the aircraft. 7.1.5 This device meets the minimum performance and quality control standards required by a technical standard order (TSO). Installation of this device requires separate approval. This device meets the performance requirements for use in transponder rule airspace as defined in 14 CFR §...
8.2 Mounting The EchoESX is designed to be mounted in any convenient location in the cockpit, the cabin, or an avionics bay. The following installation procedure should be followed, remembering to allow adequate space for installation of cables and connectors.
R485/RS232 Input Connect to Pin 6 to Select select RS232 Aircraft 11-33V Power Mating Connector: Cinch DEUH-9P Note: Use a 3A circuit breaker between the power source and echoESX. LEDs SOLID FLASHING GREEN Powered Transmitting Page 15 | 26 ECCN 7A994...
The distance between the EchoESX and the power source is limited by the impedance of the wire between them. The EchoESX is powered directly from aircraft power, and, therefore, the acceptable voltage drop in the power line is what limits the distance.
Page 18
UAV-1001191-001 not generally a good choice. For aircraft where those situations do not apply, an attractive alternative solution may be to use 3 or 4 pair data cable. Please note that not all data cable is suitable for this application. Cables with solid cores should not be used.
UAV-1001191-001 8.7 Antenna Installation 8.7.1 Supplied OEM Monopole Antenna The following considerations should be taken into account when siting the antenna. • The antenna should be well removed from any projections, the engine(s) and propeller(s). It should also be well removed from landing gear doors, access doors or other openings which will break the ground plane for the antenna.
8.7.2 Antenna Cable The EchoESX is designed to meet Class 1 requirements with an allowance of 2dB for loss in connectors and cable used to connect it to the antenna. Excessive loss will degrade both transmitter output power and receiver sensitivity.
UAV-1001191-001 9 Installation Setup The transponder system should be configured on the EFIS during initial system installation by a qualified technician. The configuration items list below should be used to document the system installation for future reference. Configuration Item Default Setting ICAO Number 0x000000...
These addresses are usually written as a 6-digit hexadecimal number, although you may also encounter one written as an 8-digit octal number. The echoESX understands the hexadecimal format, so you must first convert an octal number to hexadecimal before entering.
Both UAT and 1090 9.6 V (knots) This parameter allows the echoESX to automatically switch between airborne and ground modes. Enter the VSO value for your aircraft. Setting to 0 passes control of the Air/Ground state to the EFIS. Airspeed (in kts) that the aircraft typically flies after take-off.
UAV-1001191-001 9.8 GPS Antenna Offset The GPS antenna offset is used in conjunction with the length and width to manage taxiway conflicts. A typical GPS does not report the geographic position of the center of the aircraft, or even the tip of the nose of the aircraft;...
11 Continued Airworthiness Other than for periodic functional checks required by the regulations, EchoESX has been designed and manufactured to allow “on condition maintenance”. This means that there are no periodic service requirements necessary to maintain continued airworthiness, and no maintenance is required until the equipment does not properly perform its intended function.
UAV-1001191-001 12 Environmental Qualification Forms Nomenclature EchoESX ADS-B Mode S transponder Part Number UAV-1001190-001 Manufacturer uAvionix Inc Address 300 Pine Needle Lane, Bigfork, MT 59911 Conditions DO-160G Description of Conducted Tests Section Temperature and Altitude Equipment tested to Category B2 Low temperature ground 4.5.1...