Summary of Contents for ensto HJHP33.2402
- Page 1 PEM1268ENG INSTALLATION INSTRUCTION 2012-02 HEAT SHRINK JOINTS H-CABLE VS H-CABLE HJHP33.2402, HJHP33.2402C, HJHP33.2403, HJHP33.2403C ENGLISH...
-
Page 2: General Information
If local legislation contains provisions in respect of such training or sufficient knowledge in respect of installation of electrical equipment such provisions shall be fulfilled by the said person. - Ensto accepts no liability concerning claims resulting from misuse, incorrect installation or ignored na- tional safety regulations or other national provisions. - Page 3 HJHP33.24 PEM1268ENG 2012-02 3/12 Reference line Surplus part Surplus part Overlap the cables for at least 300 mm. Cut the cables in the middle of the overlapping (reference line). Outer covering or sheath Outer covering or sheath Inner covering or sheath PVC-tape PVC-tape Inner covering or sheath...
- Page 4 B + 20 mm from the core end. Clean the cores very carefully of extra oil. Clear the core ends about cutting pieces and dirt. Table 1. HJHP33.2402, HJHP33.2402C 190 mm HJHP33.2403, HJHP33.2403C...
- Page 5 HJHP33.24 PEM1268ENG 2012-02 5/12 Semiconductive tubes (SSET) Conductor SSET SSET SSET Place the semiconductive tubes (SSET) on the each core at the distance of B (Table 1) from the conductor towards the crutch. Shrink each tube starting from the conductor end. Core Transparent tube Conductor...
- Page 6 HJHP33.24 6/12 PEM1268ENG 2012-02 Stress control tape (SSCTA85) SSET SSET Binding SSET cord Stress control tape (SSCTA85) Belt insulation Shape a piece of stress control tape SSCTA85 to at least 30 mm length according to the picture and push it well into the crutch. The piece of the tape should fill up all the space in the crutch and the between the adjacent cores.
- Page 7 HJHP33.24 PEM1268ENG 2012-02 7/12 Repeat the steps 3 – 12 also to the other cable. Use longer transparent and semiconductive tubes. Sealing tube CPEEPL (CPEEL) Stress control tube (SISCT) Insulating and semiconductive tube (SIST) SIST SSET SSET SISCT SSBO SSBO SSET SSET SISCT...
- Page 8 HJHP33.24 8/12 PEM1268ENG 2012-02 Stress control tape (SSCTA85) Stress control tape (SSCTA85) SSET SSET Wrap two layers of stress control tape SSCTA85 on the semiconducting tube (SSET) edge on both cables. Start from the semiconductive layer side about 10 mm and cover 10 mm of transpar- ent tube.
- Page 9 HJHP33.24 PEM1268ENG 2012-02 9/12 Insulating and semiconductive tube (SIST) SISCT SSET SSET SIST Centre the insulating and semiconductive tube SIST on top of the stress control tube. Start shrinking it from the middle and move towards the ends. Tinned copper tape Lead or aluminium sheath Lead or aluminium sheath SSBO...
- Page 10 HJHP33.24 10/12 PEM1268ENG 2012-02 Tinned copper tape (8 rounds) Tinned copper braid SSITA42 tape Tinned zone Wrap tinned copper tape over the armouring. Fix the copper tape to armouring by knotting it. Set the two ground copper braids on the tinned copper tape on the lead or aluminium sheath (on the opposite sides of cable joint) so that the braids ends are on the same line as interface of outer sheath and armouring.
- Page 11 HJHP33.24 PEM1268ENG 2012-02 11/12 Sealing mastic PA22 Roughen Sealing tube (CPEEPL or CPEEL) Slide the smaller CPEEPL (or CPEEL) sealing tube so that it overlaps the previously roughened 75 mm of the cable. Start shrinking the tube from middle and move towards the ends. The tube is properly shrunk when the adhesive starts to come out from the ends.
- Page 12 UTILITY NETWORKS ENSTO FINLAND OY ENSIO MIETTISEN KATU 2, P.O.BOX 77 06101 PORVOO, FINLAND TEL. +358 204 76 21 FAX +358 204 762 770 UTILITY.NETWORKS@ENSTO.COM WWW.ENSTO.COM...