VAXIS STORM 500+ Instructions Manual

Hide thumbs

Table Of Contents

Quick Links

GM-innovations

VAXIS STORM 500+

INSTRUCTIONS

Phone: +86 731-83998739

Website: www.vaxis.cn

ADD: 8F, N0.2,Huachen Century Square,Wanjiali Street,Yuhua District,Changsha City,Hunan Province,China.

Table of Contents

Need help?

Do you have a question about the STORM 500+ and is the answer not in the manual?

Questions and answers

Summary of Contents for VAXIS STORM 500+

Page 1 GM-innovations VAXIS STORM 500+ INSTRUCTIONS Phone: +86 731-83998739 Website: www.vaxis.cn ADD: 8F, N0.2,Huachen Century Square,Wanjiali Street,Yuhua District,Changsha City,Hunan Province,China.
Page 2: Table Of Contents
Introduction ....................1 1.Cautions ....................2 2.About ......................3 3.Installation ..................... 10 4.Operation instruction ................12 5.Maintenance ..................16 6.Truble shooting ..................17...
Page 3: Introduction
Introduction  Thank you for choosing our long-range wireless HDMI / SDI HD products. Before you install the product, please read the user manual carefully and follow the manual of the user manual to avoid product damaged or other safety accidents. ...
Page 4: Cautions
1. Cautions ■Logo and meaning Careful, warning, dangerous, Pay attend to following items. ■Cautions  Do not use this product in the extreme hot, cold, dusty or humid environments.  Prevent friction with hard objects.  Avoid the product falling down from a high place, or it may damage the hardware.
Page 5: About
2. About ■Product Model and standard The VAXIS STORM 500FT+ Wireless HDMI/SDI Transmission Suite utilize today’s most advanced wireless video transmission technology, which can realize the broadcast-class and uncompressed 3G SDI/HDMI HD video signal transmitted with no compression and zero delay. The suite includes one transmitter and one receiver, both of them provides a 3G/HD SDI interface and a HDMI interface.
Page 6 ■ Main features:  HDMI 1.3 spec supports  HDMI and 3G SDI input and output  Highest resolution 1080p 60,no delay and no compression  Support audio formats include Dolby True HD, DTS-master, etc.  AES-128 encryption with air interface HD video data stream ...
Page 7 Transmitter Receiver Interface SDI Input (BNC Female); HDMI SDI Output (BNC Female); HDMI Input(Type A Female);2 Antenna Output(Type A Female);2 Antenna Interfaces;DC Input(2 Pin LEMO Interfaces;DC Input(2 Pin LEMO Female);Add a USB port to Female);Add a USB port to upgrade upgrade Supply Voltage...
Page 8 Modulation Mode OFDM 16QAM OFDM 16QAM Transmitted Power Maximum 20dBm Receive inspiration -75dBm Occupied 20/40MHz 20/40MHz Bandwidth Temperature Range 0~40°C(operating condition); 40°C (operating condition); -20~60°C(Storage) -20~60°C(Storage) Compliance FCC;CE. FCC;CE. ■Name of the product parts Transmitter: ①RP-SMA Antennae connector ②HDMI Input...
Page 9 ③SD/HD/3G SDI Input ④DC Input, LEMO 2 Pin B series connector ⑤Screen control button ⑥Optional battery buckles ⑦USB interface to upgrade ⑧DC switch ⑨1/4-20 threaded hole Receiver:...
Page 10 ①Built-in Antennas ②USB interface to upgrade ③SD/HD/3G SDI output ④HDMI output ⑤DC switch ⑥DC Input, LEMO 2 Pin B series connector ⑦V-LOCK or AB-LOCK optional plate...
Page 11  2 pieces DC conversion cable (LEMO 2 pin male to D-Type)  1 piece 3G-SDI flexible cable  1 piece Vaxis Blue Noga Arm  1 user Manual  SONY NP-F970 battery plate  V-LOCK battery plate...
Page 12: Installation
There are 3 1/4-20 screw nuts in the bottom transmitter metal case, which are located on the bottom. So the user can utilize Vaxis Noga Arm to fix the transmitter on camera. c) If the product you purchased has a battery plate, you can connect the battery corresponding to the battery plate to the transmitter.
Page 13 b) The user also can utilize a subsidiary LEMO 2 pin male to D-Type receptacle power cable to get power input from an outside power source。  Typical connection instruction Connect camera SDI or HDMI output to transmitter SDI or HDMI input port, and the transmitter can fixed in hot-shoe port of the camera.
Page 14: Operation Instruction
4. Operation instruction ■Getting started After finishing all steps above, system is workable, follow below steps. a) Ensure the video source output of the camera is OK, and the HD monitor is power on and switched to connected video input port. b) Ensure all input, output SDI or HDMI cables are connected.
Page 15 “Video”will light. Before the receiver output the normal video signal,the monitor will display an OSD of “Link connecting……” like below picture: Link Connecting... g) The system will spend about 10 seconds to complete the initialization and wireless connection. The actual connection time will be associated with the wireless environment of the specific usage scenario.
Page 16 face, and don’t turn round any sides with too big angle. The real transmission distance also relevant current electromagnetic environment, because the system works in ISM band, it is exposure to all kind od 5GHz band air interference, we suggest the users should do a manual frequency sweep by adjusting frequency selection knob with a circle before using the equipment, then choose the best frequency channel for stable performance.
Page 17 ■ Frequency Selection The wireless suite can work in 5.1-5.9GHz frequency band and be flexibly software configured to licensed or ISM band of global different regions. Meanwhile,on the side of both transmitter and receiver Set aside the manual communication channel selection knob, can use the random screwdriver to adjust the channel.Please note: Transmitter and Receiver should keep in the same channel(Similar to the intercom principle).When working together with multiple sets of products (up to 4 sets of work),...
Page 18: Maintenance
5. Maintenance ■Storage conditions Products storage temperature should be -20°C~60°C. For long time storage requirement, please use original carbon boxes, and avoid from high humid, acid base or dusty place. ■Maintenance Warning To ensure your safety, place choose well-known brand DC batteries, and guarantee suitable work conditions that battery manual mentioned.
Page 19: Truble Shooting
6.Trouble shooting ■Normal problems a) No output on display Please check the TX and RX power first, if TX or RX is powered from battery or external power,please ensure the battery or external power source can supply the power.Then check if TX antennas and RX antennas are installed right.