Advertisement
Quick Links
Advertisement
Summary of Contents for Cidron Slimline E
- Page 1 CIDRON Installation guide Cidron Slimline E Reader...
-
Page 2: Technical Specifications
Cidron Slimline E (VGE) Reader - Technical specifications Operating frequency 13,56MHz. MIFARE® CSN 4 byte, MIFARE® CSN 7 byte, MIFARE Classic®, MIFARE Plus, MIFARE® DESFire® 0.6 and MIFARE® DESFire® EV1. Also supports other ISO 14443 A/B* compatible cards. Reading technologies *Not all ISO14443 B cards have been implemented in the reader, please contact Nexus for more details on current status. - Page 3 Package content: • 2pcs Installation screws • 1pc Installation plate • 2pcs Screw plugs • 1pc Reader module with front plate • 1pc Cable strip • 1pc Front cover • 1pc Fixing screw • 1pcs Terminal connector (10-pin) • 1pc Quick installation guide * Please note that all pictures in this manual are illustrations and do not represent the actual sizes and form of the components.
- Page 4 ~20 cm In order to facilitate installation a cable length of 20cm is recommended.
- Page 5 Ensure that the installation plate is fixed in the correct direction, i.e. the arrows pointing upwards.
- Page 6 113mm 44mm 10mm When installing directly to wall or door, use the installation holes as picture describes. If using other screws than the ones supplied with the reader, make sure to use a flat headed screw with a maximum height of 2.8 mm and a maximum diameter of 7.8 mm on the screw head.
- Page 7 P3 - Black Socket Make sure to place the terminal connector with the fastening screws facing towards you.
- Page 8 R-LED G-LED Black Description Wiegand RS232 External Buzzer control R-LED External Red LED control G-LED External Green LED control Ground Wiegand Data1 Wiegand Data0 RS232 - RS232 + Ground Power supply 9-12 VDC 1. Maximum wiegand cable length is 150 meters and requires a high quality shielded cable with minimum AWG18 dimension (=0.8231mm2) in an environment free from electrical noise.
- Page 9 Make sure no excess connection cable is left in between the reader module and the installation plate. Use the enclosed cable strip to fix the cable in the cord grip. It is recommended to connect the the wires to the terminal connectors before tightening the cable strip.
- Page 10 When installing the reader to the mounting plate ensure that the reader pin header contact perfectly aligns with the terminal connector block.
- Page 11 Mount the front cover as per the image above and make sure it is fitted correctly. In order to do so, allign and fit the top snap fastening, apply and main- tain pressure on the top of the front cover while sliding the front cover over the bottom snap fastening.
- Page 12 To secure the front cover to the reader use the supplied fixing screw and fix it into the installation plate through the front cover.
- Page 13 Cidron tool, part no: SC9914 To open the reader, first remove the fixing screw and then detach the front cover from the installation plate by inserting the tip of the tool into the slot at the bottom of the front cover and move the tool upwards.
- Page 14 Overview, programming of reader Setting the reader in programming mode see page: Configuring the Changing reader authentication card see page: see page:...
- Page 15 Setting the reader in programming mode BEEP ! Reading distance approximately 2 cm. In order to set the reader in programming mode, present the valid “Authentication Card” to the reader as shown. The reader will beep and start blinking yellow to indicate that it is now in programming mode.
-
Page 16: Configuring The Reader
Configuring the reader BEEP ! Reading distance approximately 2 cm. 1: Set the reader in programming mode, see page: 16 2: Present the “Configuration Card” to the reader as shown. Keep the card within reading distance until the reader beeps and blinks in green. The reader is now programmed and ready for use according to the configuration settings on the configuration card. - Page 17 Changing authentication card BEEP ! Reading distance approximately 2 cm. 1: Set the reader in programming mode, see page: 16 2: Present the “CHANGE Authentication Card” to the reader as shown. Keep the card within reading distance until the reader beeps and blinks in green.
- Page 18 CIDRON Accessories Cidron Slimline E Reader...
- Page 19 Distance plate, Slimline E Matte black, part no: SC9291-S Matte white, part no: SC9291-V The distance plate can be used for example when installing readers in environments where the installation surface is uneven or/and external wiring at the same side as the reader.
- Page 20 Distance plate, large, Slimline E Matte black, part no: SC9297-S Matte white, part no: SC9297-V Used to install readers on an area where additional cover is needed to hide old installation holes or on uneven surfaces. Can also be used...
- Page 21 Distance plate, angled 10° Slimline E Matte black, part no: SC9293-S Matte white, part no: SC9293-V Used to increase accessibility as well as visibility of the keypad.
- Page 22 Distance plate, angled 33° Slimline E * Screws and screw plugs included with accessory. Matte black, part no: SC9292-S Used to increase accessibility as well as visibility of the keypad. Recommended height is 900mm (center of reader) above the ground/floor.
- Page 23 Vandalization protection Slimline E * Screws and screw plugs included with Matte black, part no: SC9280-S accessory. The vandalization protection is an accessory that shields the reader and helps it withstand violence by absorbing and redirecting external forces away from the reader. Can be retro-fitted to already installed...
- Page 24 Distance plate, large + Vandalization protection, Slimline E A recommended combination when external wiring is needed together with the vandalization protection. Can also be used for covering up old installation holes.
- Page 25 Climate- & Privacy protection * Screws and screw plugs included with Transparent, part no: SC9901-T accessory. White, part no: SC9901-V The transparent version SC9901-T is recommended to use for in- creased protection from rain and snow while still providing great visibility and accessibility in a slender format.
-
Page 26: Cleaning Instructions
Cleaning instructions Use compressed air in between the buttons to remove dust and dirt and after that Isopropyl alcohol can be used with a piece of fabric to rub in between the buttons and the reader exterior. - Page 27 The Cidron reader family are intended for; Sale to professional security companies and installation by experienced security professionals. Nexus Group can not provide assurance that any entity or person buying or obtaining the product is properly experienced or trained to correctly install security related products including card readers.