Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cosco SX4444
Summary of Contents for Cosco SX4444
- Page 1 TREADMILL MANUAL SX4444...
- Page 2 Thanks for buying our Fitness equipment, Do some warm-up exercise before use, you’ll get twice the result with half the effort. Such as follows: extend the neck up and down twist the waist left and right level push forwards upright straighten one's back - 2 -...
-
Page 3: Safety Guidelines
left and right poise exercise up and down extend exercise thigh extend exercise calf extend exercise SAFETY GUIDELINES: Before beginning any exercise program, you should consult with your doctor. It is recommended that you undergo a complete physical examination. Please follow the instructions: 1. - Page 4 8. Keep hands away from moving parts 9. Please note that there is a weight limitation for this product. If your weight more than 140kgs. It is not recommended that you use this product. Serious injury may occur if the user weight exceeds the limit shown here. This product is not intended to support users whose weight exceeds this limit.
- Page 5 EXPLORE DRAWING - 5 -...
-
Page 6: Part List
PART LIST PART NO PART NAME Q'TY Frame of handlebar Frame of computer Left upright Right upright Base frame Incline frame Running platform Up cover of computer Computer belly pan 10-1 Up cover of pulse handlebar 10-2 Bottom cover of pulse handlebar Cup frame Safety key Tube plug of handlebar... - Page 7 Speed sensor Base frame of motor Incline motor Transformer Control board Plug Power wire cushion Fuse Power key Power wire Computer control board Connect wire of handlebar Connect wire of upright Connect wire of base frame ST4.2*15 Screw ST2.9*10 Screw M8*20mm Allen head bolt M8*20mm Allen head bolt M10*50mm Allen head bolt...
-
Page 8: Hardware Comparison Chart
M8*65mm Allen head bolt Supportive cushion of running deck M8*85mm Allen head bolt M8*50mm Allen head bolt M8*20mm Allen head bolt Ø8 Spring washer M5*10 Bolt Ø5 Spring washer ST2.9*8Screw M8*70mm Allen head bolt M8*12mm Allen head bolt M10*50mm Allen head bolt Ø12 Plastic washer M10*60mm Allen head bolt ST4.2*12 Screw... -
Page 9: Assembling Instructions
ASSEMBLING INSTRUCTIONS WARNING: Please put on all the screws, washers and bolts then tighten them. STEP1: 1. Fix the protective cover of upright on the base frame with ST4.2*15 Screw 58. - 9 -... - Page 10 ENSURE PINS ARE STRAIGHT ATTENTION: Be careful when you connect the two console-controller wires. There are pins inside connector, the pins must be straight, and otherwise it will cause problems. STEP2: 1. Fix the uprights on the base frame with M10*50mm Allen head bolt 54, M10*60mm Allen head bolt 55, Ø10 Washer 56 and M10 Nylon nut 57.
- Page 11 STEP4: 1. Connect the wire of handlebar 47 and the wire of computer control board 46. 2. Fix the computer with M8*20mm Allen head bolt 52. STEP5: Folding illustration: To unfold the treadmill 1 Strike the damper.( as shown by the arrow on top left) 2.
-
Page 12: Computer Operation
To fold up the treadmill: 1. Hold the bottom end covers (arrows showing in the left and right side) and lift the treadmill. COMPUTER OPERATION Panel layout - 12 -... -
Page 13: Key Instruction
The Operation Power The required main power is 220 - 240 VAC ◆KEY INSTRUCTION START: Presses START key to start the treadmill. STOP: Press STOP key for two seconds to stop the treadmill but press it in two seconds to pause the treadmill. - Page 14 WAITING MODE Press MODE key to change the NORMAL MODE-TIME MODE-DISTANCE MODE-CALOREIS MODE-P1……P18-HRC65%-HRC85% -USER1-USER2-USER3-USER4-NORMAL MODE in turns. The setting mode will flash. TIME MODE The default time is 30 minutes. Press SPEED+/SPEED- key to adjust the target time of 10:00-99:00. Presses START key to enter the running mode after the 3 seconds.
-
Page 15: Running Mode
Press INCLINE+/INCLINE- key to adjust the incline value of 0%-15%. Presses START key to enter the running mode after the countdown of 3 seconds. Press STOP key for two seconds to stop the treadmill but press it in two seconds to pause the treadmill. When change the level, there will be BBBBB warning sounds. - Page 16 MODE-P1……P18-HRC65%-HRC85%USER1-USER2-USER3-USER4-NORMAL MODE in turns. The setting mode will flash. Choose the USER1-USER4. The default time of USER is 30 minutes. Press SPEED+/SPEED- key to adjust the target time of 10:00-99:00. Press ENTER key to enter the setting of every level. Press SPEED+/SPEED- to adjust the speed value and INCLINE +/INCLINE- key to adjust the incline value.
- Page 17 ◆ PROGRAM SPD INC SPD INC SPD INC SPD INC SPD INC SPD INC - 17 -...
- Page 18 SPD INC SPD INC SPD INC SPD INC SPD INC SPD INC - 18 -...
- Page 19 SPD INC SPD INC SPD INC SPD INC SPD INC SPD INC - 19 -...
-
Page 20: Maintenance
◆ Error Message Resolution Error Specification Treatment Replace the connecting cables. Connect error between Check that the lines between console Replace the device. panel and controller and driver are connected or not. Replace the panel. Replace the adapter. Replace the device Error on motor/MOS crash Check that the line to motor is Replace the motor... -
Page 21: Belt Adjustment
4. Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill. Vacuum the underneath treadmill once a week. BELT ADJUSTMENT: Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been adjusted properly at the factory. -
Page 22: Deck Lubrication
DECK LUBRICATION: The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance. Every 3 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can reach.
Need help?
Do you have a question about the SX4444 and is the answer not in the manual?
Questions and answers