Download Print this page

Lithe Audio 06300 Installation Manual

Remote control motorized 90o wall mount 32-60''

Advertisement

Quick Links

LEARN MODE instructions as shown below:
STEP1: Press and hold
for 5 seconds until LED light on the matched remote control stays on, and
then press
. The buzzer will sound once, the red LED light on the IR receiver will stay on, then the
LEARN MODE will be entered.
STEP2: If LEARN
, please press
on the matched remote control until the buzzer sounds twice,
the red LED light on the IR receiver will change from being steady to a slow flash.
STEP3: Aim the TV remote at the IR receiver, and press the button on the TV remote that you need to set as
the function of
button until the buzzer sounds three times. the red LED light on the IR receiver will
change from slow flash to a fast flash.
STEP4: Press
button on the matched remote control until the buzzer sounds four times. The
red LED light on the IR receiver will turn off.
sounds once, then a LEARN failure.(The TV remote won't support the LEARNING function).
(Please follow step1 through step4 in turn if the user need to LEARN more buttons)
Learn "Power" button on the TV remote:
Press and hold
for 5 seconds until LED light on the matched remote control stays on , and then press
The buzzer will sound once, the red LED light on the IR receiver will stay on, then press and hold
on the matched remote control until the buzzer sounds twice, then release the
light on the IR receiver will change from being steady to a slow flash.
Aim the TV remote at the IR receiver, and press "Power" button. The buzzer will sound three times. The red
LED light on the IR receiver will change from slow flash to a fast flash. Press
remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn off. "Power"
button will be LEARNED successfully. If press "power" button, the TV wall mount will automatically reset.
Note: When there is no activity for over 20 seconds in any step .TV remote will automatically exit from the
LEARN MODE.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
15
button will be LEARNED successfully. If the buzzer only
button. The red LED
button on the matched
REMOTE CONTROL MOTORIZED
.
button
90
WALL MOUNT 32-60"
O
INSTALLATION MANUAL
CAUTION:
DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
200x200
300x300
400x200
400x400
60"
40kg
40kg
MAX
(88lbs)
(88lbs)
RATED
RATED

Advertisement

loading

Summary of Contents for Lithe Audio 06300

  • Page 1 LEARN MODE instructions as shown below: STEP1: Press and hold for 5 seconds until LED light on the matched remote control stays on, and REMOTE CONTROL MOTORIZED then press . The buzzer will sound once, the red LED light on the IR receiver will stay on, then the LEARN MODE will be entered.
  • Page 2: Component Checklist

    Component Checklist NOTE: Read the entire instruction manual before you start installation and assembly. IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement. WARNING •...
  • Page 3 1. Separating the Decorative Covers from the Wall Mount 4a. For Wood Stud Wall Mounting Forward installation Find and mark the exact location of mounting holes 2.Opening Hard the Swing Arm Drill pilot holes 90° √ Reverse installation 3. Position the Swing Arm Remove the screws and washers using the proper phillips screwdriver.
  • Page 4 4b. For Solid Brick and Concrete Mounting Forward installation Mark the exact location of mounting holes Drill pilot holes √ Reverse installation √ Screw the wall mount onto the wall Tighten the screw leaving a 7mm space from the wall. WARNING Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Page 5 5. Installing the Decorative Covers and the Cable Clips √ Screw the wall mount onto the wall...
  • Page 6 6. Installing the Adapter Brackets 6-2 For Recessed Back Screens or to Access A/V Inputs Remove the screws on the adapter brackets and keep the screws for later use. 6-1 For Flat Back Screens M-D/M-E M-D/M-E M-C/M-D/M-E Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen. ·...
  • Page 7: Cable Management

    7. Hooking the TV onto the Wall Mount 8. Cable Management 90° Hook the TV over the swing arm. Reinstall the bottom screws to secure the adapter brackets to the swing arm. 90° Important:Make sure the TV is correctly hooked before releasing the TV. To avoid the little tilt caused by weight, you can tighten the Connect the cables to your TV and route through the cable clips.
  • Page 8 9. Placing the IR Receiver Do not open the electrical cover please. wall mount automatically stop at 90°position.) STEP 3: Press and release to return the TV wall mount flat against the wall and hear one beep from the buzzer, the system will then enter a working condition. Buttons function instructions Follow the Key function instructions below to operate.