Table of Contents
Advertisement
2.5.3 Shut-Down Procedure
No shut-down procedure is required for the Pressureless
Cooker except to check that the timer dial is in the OFF
position and the compartment door are open. Consult the
steam boiler instruction plate and complete the shut-down
procedures for the boiler.
2.6 Reversing the Doors
The Pressureless Steam Cooker has a reversible cooking
compartment door. This section contains instructions for
reversing this door.
1. Turn off power to the unit.
2. Open the cooking compartment door
3. Remove the two screws that attach the top hinge to the
front of the unit.
4. Slide the door upwards, off the bottom hinge.
5. Remove the two screws that attach the bottom hinge to
the front of the units.
6. Remove the right and left side panels by unscrewing the
1 screw on each panel and sliding the panel down.
7. Remove the door interlock assembly by unscrewing the
two nuts that hold it in place (assembly is attached to
the screws in the top right hinge mounting holes, see
fig. 2-1).
8. Remove the four screws in the right side hinge
mounting holes and install them in the left side hinge
mounting holes (where the hinges were originally
mounted).
9. Using the nuts removed in step #6, reinstall the door
interlock assembly onto the 2 screws in the lower left
hinge mounting holes (see fig. 2-1) with by moving the
assembly over the cooking cavity to the other side of the
unit. Rotate the door interlock assembly 180° for
installation, so that the switch is now facing up.
10. Reinstall the top hinge and screws into the right lower
hinge mounting holes. Rotate the hinge 180° for
installa- tion, so that the pin which the door rides on is
now facing up. The hinge must be rotated because it
will now function as the bottom hinge. DO NOT
COMPLETELY TIGHTEN THE HINGE MOUNTING
SCREWS YET. These will be used later for adjusting
the door.
11. Remove the door latch assembly from the face of the
unit. The 2 nuts mounting the door latch are located
behind the face of the unit and must be accessed
where the right side panel was removed.
SECTION 2 INSTALLATION
12. Remove the two white hole plugs from the left door
latch mounting holes, and insert them into the right
door latch mounting holes (where the door latch
assembly was originally mounted).
13. Rotate the door latch assembly 180°, and install into
the left door latch mounting holes.
Each stud on the latch assembly should have a plastic
washer, a spring, a plastic washer and a Nyloc type nut.
14. To adjust the tension of the door latch, tighten both
nuts down until the springs are fully compressed, then
back each nut off 1 1/2 turn.
15. Rotate the door 180° for mounting.
16. Slide the remaining hinge into the top door bearing.
17. Slide the door and hinge assembly down onto the
hinge which you have already mounted to the front of
the unit. Use the two screws to mount the top hinge
into the right upper hinge mounting holes. DO NOT
COMPLETELY TIGHTEN THE HINGE MOUNTING
SCREWS YET.
18. Slowly push the cooking compartment door closed
until it is latched.
19. The cooking compartment door can now be raised,
lowered, and/or rotated into position by bumping it with
the palm of your hand or by using a small rubber
mallet.
20. First, check the alignment at the front of the door by
making sure that the striker in the door is centered with
the latch mechanism on the front of the unit.
21. Square the door to the unit by raising or lowering the
hinge side of the door, keeping the latch centered with
the striker.
22. Visually inspect the door. Be sure that the door is
square to the unit, the striker is centered with the latch,
and the gasket is in contact with the entire lip of the
cooking compartment.
23. Gently open the cooking compartment door, taking
care not to move it out of position.
24. Tighten all 4 door hinge bracket mounting screws.
25. Close and visually inspect the door again, as
described in step 22.
26. Reinstall the left and right side panels, using the
screws for each panel.
2-2
NOTE:
Advertisement
Table of Contents
