Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for THOMAS DÖRR TD 3000L M14
Summary of Contents for THOMAS DÖRR TD 3000L M14
- Page 1 Operating instructions Cutlery polishing machine TD 3000L M14 Kitchen and Cutlery Systems Hettenbergring 47 D-74889 Sinsheim Tel.: +49 (0)7261 / 9754-93 Fax: +49 (0)7261 / 9754-94 08/2017 English translation of the original operating instructions manual...
-
Page 2: Table Of Contents
Table of Contents 1. GENERAL INFORMATION 1.1 I NTRODUCTION 1.2 E XPLANATIONS 1.3 D ELIVERY ONTENTS 2. SAFETY 2.1 P ROPER USE 2.2 I MPROPER USE 2.3 G ENERAL SAFETY INSTRUCTIONS 3. SHIPPING, STORAGE AND SET UP 3.1 S HIPPING 3.2 S TORAGE 3.3 U... -
Page 3: General Information
1. General Information 1.1 Introduction This instruction manual contains useful information on the use and service of the cutlery polisher and must be read thoroughly before the machine is put into operation. Requirements for operating and maintenance personnel Anyone working on or with the machine, whether its initial start-up, installation, operation, or maintenance is required to read and understand this operating instructions manual. -
Page 4: Safety
2. Safety 2.1 Proper use The intended use of the machine is only drying and polishing chrome, steel, or silver cutlery. The following cutlery pieces can be used: ► spoon ► fork ► knife ► small fork ► tea spoon 2.2 Improper use The machine is not designed to polish any other sorts of cutlery or foreign utensils. -
Page 5: Shipping, Storage And Set Up
3. Shipping, storage and set up 3.1 Shipping The following steps must be followed when the machine is being, or has been transported: ► Never tilt or turn over the machine ► Check the machine in advance for any damage caused by the shipment ►... -
Page 6: Removing The Transportation Safety Device
3.5 Removing the transportation safety device Instructions for removing the transportation safety device: 1. Open the top cover and remove the 2. Loosen and remove the wing nut by Star grip by loosening it turning it counter clockwise 3. Remove transportation safety device 4. -
Page 7: Handling
4. Handling 4.1 Before initial operation Initial operation is only allowed when ► the machine has been checked for complete sufficiency ► the set up conditions have been followed ► the transportation safety device has been removed ► the instruction manual has been read completely ►... -
Page 8: Start Up And Operation Of The Cutlery Polishing Machine
4.3 Start up and operation of the cutlery polishing machine CAUTION! Never install or operate the machine with a damaged power cord. By suspicion of damage, for example an electrical fault smell, disconnect the machine from the power circuit immediately and contact the Dörr-service personal. -
Page 9: Cleaning And Maintenence
5. Cleaning and maintenance CAUTION! Risk of serious injury or death by means of electrical shock Before any maintenance or cleaning jobs are performed always assure the rocker switch is switched to “O” and the power plug is removed from the power circuit 5.1 Daily cleaning Clean the cutlery polishing machine daily by following these Steps: 1. -
Page 10: Replacing The Uvc Lamp
5.3 Replacing the UVC Lamp To assure sterilisation of the granulate, replace the UVC lamp after 8000 operating hours. Replacement of the lamp is shown on the pictures below. Before replacing the UVC lamp turn the machine off by switching the rocker switch to “O” and disconnect the power plug from the electrical socket. -
Page 11: Troubleshooting
6. Troubleshooting Malfunction / Solution Possible causes Problem Granulate sticks to Cutlery is still Wash the cutlery again thouroughly and insert into cutlery dirty. the machine again. If granulate pieces no longer stick to the cutlery then the problem was the dishwashing results. - Page 12 Continued on the following page Malfunction / Solution Possible causes Problem Granulate dust New granulate. Fresh granulate can cause more dust deposits at particles on cutlery first. When the granulate has been heated up as required, dump 4-5 shot glasses of water into the feed chute of the machine.
- Page 13 Continued on the following page Malfunction / Solution Possible causes Problem Machine does not Top cover is not Close the top cover. start closed. Damaged Fuse. Check the fuses and have them replaced by an authorized service technician. Power plug may Check if the power plug is inserted correctly.
-
Page 14: Accessories For The Cutlery Polishing Machine
7. Accessories for the cutlery polishing machine The following accessories can be ordered with your cutlery polishing machine TD 3000L M13: Picture Name Description Mobile underframe with fixation for a secure stand of the cutlery polisher. Mobile underframe TD With an extendable drawer for a cutlery basket. 3000L with extendable For an optimized working height of the machine. -
Page 15: Company Address
(See illustration on page 7). Kitchen and Cutlery Systems Hettenbergring 47 D-74889 Sinsheim Tel.: +49 (0)7261 / 9754-93 Fax: +49 (0)7261 / 9754-94 9. Technical data TD 3000L M14 Capacity 3000 cutlery pieces per hour Consumption 550 W Weight 50 kg... -
Page 16: Ce - Declaration Of Conformity
EU Guidelines in terms of its design and construction as well as the version put into circulation by us. Any modification to the machine not coordinated with us invalidates this Declaration of Conformity. Description of the machine: Cutlery polishing machine Type: TD 3000L M14 Applicable EU Machine Guidelines (2006/42 EG) EU Guidelines: EMC Guidelines (2014/30 EU) -
Page 17: Notes
MAX DÖRR GmbH -Förderanlagen- Gemmingen, 13.04.2016 ___________________________________ (Thomas Dörr, CEO) 12. Notes Page 17 of 18... - Page 18 Page 18 of 18...
Need help?
Do you have a question about the TD 3000L M14 and is the answer not in the manual?
Questions and answers