Baby Bullet User Manual And Recipe Book page 4

CLEANING SAFEGUARDS
• DO NOT PUT THE BABY BULLET BLADE HOLDERS AND OTHER PLASTIC PARTS
IN THE DISHWASHER. SIMPLY HAND WASH WITH WARM SOAPY WATER.
• DO NOT SUBMERGE THE POWER BASE IN WATER. WIPE OFF WITH A DAMP
CLOTH. ALWAYS UNPLUG BEFORE CLEANING.
• THE BABY BULLET BLADE HOLDERS AND OTHER PLASTIC PARTS SHOULD
NOT BE STERILIZED IN BOILING WATER OR STEAM FOR ANY REASON AS THIS
WILL WARP THE PLASTIC.
• WHEN WASHING BLADES, DO NOT ATTEMPT TO REMOVE THE GASKET RING.
SIMPLY HAND WASH THE BLADES IN WARM SOAPY WATER.
• DO NOT EXPOSE BLADE HOLDERS AND OTHER PLASTIC PARTS TO
EXTREME RAPID TEMPERATURES CHANGES, AS THIS MAY WARP OR DAMAGE
THE PLASTIC.
CLEANING THE BABY BULLET
Everyone hates cleaning up, which is just one more reason the Baby Bullet is such
a wonderful time saver. You can make and cook fresh, homemade baby food from
scratch and only use one vessel! Imagine creating tasty purées, wholesome soups and
fantastic mini-meals — or turning the family's spaghetti dinner into a delicious meal fit
for Baby — with just a single cup and blade! It doesn't get any easier than that!
WASHING THE BABY BULLET
Cleaning the Baby Bullet is so easy. Simply hand wash any of the pieces (except for
the Power Base) with room temperature soapy water and rinse.
WARNING:
• DO NOT PUT THE BABY BULLET BLADE HOLDERS AND OTHER PLASTIC PARTS
IN THE DISHWASHER. SIMPLY HAND WASH WITH WARM SOAPY WATER.
• DO NOT SUBMERGE THE POWER BASE IN WATER. WIPE OFF WITH A DAMP
CLOTH. ALWAYS UNPLUG BEFORE CLEANING.
• THE BABY BULLET BLADE HOLDERS AND OTHER PLASTIC PARTS SHOULD
NOT BE STERILIZED IN BOILING WATER OR STEAM FOR ANY REASON AS THIS
WILL WARP THE PLASTIC.
• WHEN WASHING BLADES, DO NOT ATTEMPT TO REMOVE THE GASKET RING.
SIMPLY HAND WASH THE BLADES IN WARM SOAPY WATER.
• DO NOT EXPOSE BLADE HOLDERS AND OTHER PLASTIC PARTS TO EXTREME
RAPID TEMPERATURES CHANGES, AS THIS MAY WARP OR DAMAGE THE PLASTIC.
GASKET CARE
Each Baby Bullet Blade Holder incorporates a silicon gasket that creates an airtight
seal with the Baby Bullet cups. Never attempt to remove the gasket ring from a Blade
Holder. Attempted removal of the gasket may permanently damage the blade
configuration and cause leakage. If in time a gasket becomes loose or damaged,
please contact customer service for a replacement Baby Bullet Blade Holder at:
1-855-514-6922.
BE SURE TO INSPECT THE GASKET AFTER THE FIRST USE AND EACH
SUBSEQUENT USE TO MAKE SURE IT WAS INSTALLED AND HAS NOT BECOME
LOOSE OR DAMAGED.
STUBBORN CLEANUP
If ingredients dry inside the Baby Bullet, make your clean up a snap by filling the
cup half full with soapy water twist on the blade and blend it for 10-20 seconds on
the power base. That will loosen the stuck ingredients and with a light scrub, you'll
be all done.
DO NOT USE ANY OF THE BABY BULLET COMPONENTS (CUPS, LIDS, BLADES,
BATCHBOWL, BATCH TRAY, MOTOR) IN THE MICROWAVE OVEN FOR ANY REASON.
CLEANING THE BABY BULLET POWER BASE
For the most part the Power Base doesn't really get dirty, but if you neglect to
twist the blade on to the cup tightly, liquids can leak out and get into the base and
activator buttons.
Here's how to clean it up.
Step 1:
The most important thing is to UNPLUG the Power Base!
Step 2:
Use a damp rag to wipe down the inside and outside of the Power Base.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN
THE DISHWASHER
• NEVER PUT YOUR HANDS OR UTENSILS NEAR THE MOVING BLADE AND
NEVER USE YOUR HANDS OR UTENSILS TO PRESS THE ACTIVATOR BUTTONS
DOWN WHILE THE POWER BASE IS PLUGGED IN.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
This appliance has a polarized plug (one prong is wider than the other). To reduce
the risk of electric shock, this plug will only fit in a polarized outlet one way. If
the plug does not fit easily into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not modify the plug or outlet in any way.