Important Safety Instructions - Jet AFS-1000B Operating Instructions And Parts Manual

IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1. FOR YOUR OWN SAFETY, READ
INSTRUCTION MANUAL BEFORE
OPERATING THE TOOL. Learn the tool's
application and limitations as well as the
specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working
order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped
with three prong plug, it should be plugged into
a three-hole electrical receptacle. If an adapter
is used to accommodate a two prong
receptacle, the adapter lug must be attached
to a known ground. Never remove the third
prong.
5. KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
6. DON'T USE IN DANGEROUS
ENVIRONMENT. Don't use power tools in
damp or wet locations, or expose them to rain.
Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY. All
children and visitors should be kept a safe
distance from work area.
8. MAKE WORKSHOP CHILDPROOF. Use
padlocks, master switches, or remove starter
keys.
9. DON'T FORCE TOOL. It will do the job better
and be safer at the rate for which it was
designed.
10. USE RIGHT TOOL. Don't force tool or
attachment to do a job for which it was not
designed.
11. WEAR PROPER APPAREL. No loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry to get caught in moving parts.
Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
12. ALWAYS USE SAFETY GLASSES. Wear
safety glasses (must comply with ANSI Z87.1).
Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.
Also use face or dust mask if cutting operation
is dusty.
13. SECURE WORK. Use clamps or a vise to
hold work when practical. It's safer than using
your hands and frees both hands to operate
tool.
14. DON'T OVERREACH. Keep proper footing
and balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION.
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
16. DISCONNECT TOOLS before servicing and
when changing filters.
17. USE RECOMMENDED ACCESSORIES. The
use of accessories and attachments not
recommended by manufacturer may cause
hazards or risk of injury to persons.
18. AVOID ACCIDENTAL STARTING. Make sure
switch is in "OFF" position before plugging in
power cord.
19. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the fan
blade is accidentally contacted.
20. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that is
damaged should be carefully checked to
ensure that it will operate properly and perform
its intended function-check for alignment of
moving parts, binding of moving parts,
breakage of parts, mounting, and any other
conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced.
21. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Don't
leave tool until it comes to a complete stop.
22. DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol or any medication.
23. MAKE SURE TOOL IS DICONNECTED
FROM POWER SUPPLY while motor is being
mounted, connected or reconnected
WARNING: This product can expose you to
chemicals including lead which is known to the
State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to http://www.p65warnings.ca.
gov.
WARNING: Drilling, sawing, sanding or
machining wood products generates wood dust
and other substances known to the State of
California to cause cancer. Avoid inhaling dust
generated from wood products or use a dust
mask or other
protection.
Wood products emit chemicals known to the
State of California to cause birth defects or
other reproductive harm. For more information
go to http://www.p65warnings.ca. gov/wood.
2
safeguards for personal