FLM-520 User’s Guide 7-2) Geometry Menu 7-2-1) Auto-Adjustment 7-2-2) H. Position 7-2-3) V. Position 7-2-4) H. Total 7-2-5) Auto Phase 7-2-6) Delay 7-3) Contrast Menu 7-3-1) Auto-Balance 7-3-2) Contrast 7-3-3) Red 7-3-4) Green 7-3-5) Blue 7-4) Info 7-5) Input Type...
Page 4
FLM-520 User’s Guide FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferences to radio communications.
Page 5
Digital/NTSC/PAL is optionally supported 1-2) Features FLM-520 (15 inch) is the best choice at any applications of financial, industry, government in which working pace, weight and reliance should be thought. This 15 inch LCD monitor provides a viewing area equivalent to a 17 inch CRT monitor.
Page 6
FLM-520 User’s Guide 2. Components & Parts names 2-1) Components Figure 2-1) : Components 2-2) Front & Rear View Figure 2-2) Front View Figure 2-3) Rear View...
Page 7
FLM-520 User’s Guide 3. Installation 1) Connect the input plug to FLM-520 LCD monitor. (Connect 15 pin RGB connector, for analogue RGB input, to FLM-312 as shown Figure 2-3). 2) Connect the 12V Adapter to FLM-520. (When you turn on power switch, LED on the board will light Red, Green in turn and then green will remain.
Page 8
A speaker plug is ready at the rear of this LCD monitor. It is installed as follows; 1) Connect the PC Audio jack to FLM-520 Speaker plug.(1.5W 8 Ohm, Stereo) 2) Select Speaker volume at OSD initial Menu and then adjust the volume.
Page 9
FLM-520 User’s Guide 5. External Keypad 5-1) External Keypad AT the rear left side External Keypad is ready for user’s interface, it is configured as below : Sel(Down) - (Left) +(Right) Power Switch Menu Figure 5-1) External Keypad Block Diagram If MENU button is pressed, the OSD MENU is displayed.
Page 10
A warning message as in Figure 6-1 is displayed when the system detects that an RGB Video cable is not connected to the FLM-520 monitor. The message is displayed for a maximum of 10 seconds until the cable is connected.
Page 11
The OSD main Menu is displayed when the Menu keypad push button is pressed when FLM-520 powered on, and inputs & outputs properly connected. The OSD menu display is a combination of graphics and text as in Figure 7. The selected or active menu item is indicated in blue color as below.
Page 12
FLM-520 User’s Guide 7-1) RGB Menu RGB item is used to adjust the image color and brightness. Indicated number shows the present brightness value as Figure 7-1. The range of adjustment is –127 to 127. The RGB value is adjusted according to the input selected.
FLM-520 User’s Guide 7-2) Geometry Menu This Menu is used to adjust screen position of the monitor by adjusting Clock (Pixel) numbers per a line or automatically. Auto Adjustment H Position V Position H Total Auto Phase Delay Main Menu...
FLM-520 User’s Guide 7-3) Contrast Menu Contrast Menu is used to adjust image contrast. The range of adjustment can be changed according to the screen Mode. Auto Balance Contrast Green Blue Main Menu 7-3) Contrast Menu Auto Balance Makes the image contrast optimized by searching for the PC Graphic condition.
FLM-520 User’s Guide 7-4) Info Can check Firmware Version, Model number of FLM-520 LCD monitor. FLM-520 Version 1.x Finecom Co., Ltd. URL:www.finecom.co.kr Figure 7-4) Info 7-5) Input Type Setups the Input Type. Caution) Digital Input, NTSC/PAL are optional. Even in case the user did not choose the option, Digital Input and NTSC/PAL are displayed in the OSD Menu but they are not operating.
7-6) Auto Config Makes the screen condition optimized by searching screen condition. 7-7) NVRAM Init Initializes the saved value of FLM-520 NVRAM when the power turns off. Even though you selected NVRAM, the present value is not changed. 7-8) Power Down Changes Board LED to Red and cuts off the power of LCD panel.
“ screen is not displayed because video mode not supported by FLM-520 is set”. It is not necessary to inevitably install FLM-520 Windows driver. But when installed, supported resolution and revival frequency(screen return/frequency) are indicated in the list. Accordingly, the user cannot set resolution and frequency not supported by this device so that the monitor’s non-operation by the user’s mistake can not happen.
FLM-520 User’s Guide 10. Problems and Check Points * No Image shows up: - Check if the power indicator is on. - Check if you turned on the power S/W. - See that Power cable is connected well. - Ensure any pin of connectors are not broken or crooked.
Page 20
FLM-520 User’s Guide Table 2: Supported RGB PC Graphics Input Formats VESA MODES Horizontal Vertical Mode Resolution Nominal Nominal Sync Nominal Sync Nominal Total Frequency Polarity Frequency Polarity Pixel +/- 5kHz +/- 1 Hz Clock (MHz) VGA(6) 640x480@60Hz 800x525 31.649...