Summary of Contents for Actev Arrow
- Page 1 BODY KIT ASSEMBLY INSTRUCTIONS Please check for the latest version of these instructions at actevmotors.com/support/...
-
Page 3: Choking Hazard
Body Kit. Body Kit and using the product without adult supervision. The Formula Racecar Body Kit is to be used with the Arrow Smart-Kart as an Formula Racecar Body Kit is a trademark of Actev Motors, Inc. Names of aesthetic accessory only and does not provide any additional structural products, brands, etc., appearing in this manual are trademarks or registered... - Page 4 Decal Sheets x4 Bolt A x1 Screw B x4 Screw C x4 Nut A x1 Nut B x4 Screw D x6 (already installed in Arrow upper steering clamp) Rear Wing Right Pod Allen Wrench x1 Right Wing Support Front Nose...
- Page 5 BODY KIT ASSEMBLY - SIDE PODS Provided Parts Left Pod x1 Right Pod x1 10mm 13mm Open-End Wrench x1 19mm On each side of the Arrow locate the two frame holes closest to the rear wheels. ACTEVMOTORS.COM BODY KIT ASSEMBLY - SIDE PODS | 3...
- Page 6 Tighten studs until they touch the pod “L” brackets. Do not overtighten. Helpful tip: It might take over 10 half-turns to tighten each stud. Push pod toward the Arrow while tightening. You may also carefully tilt the Arrow to rest sideways on two wheels. This position may provide easier access to tighten the pod studs.
- Page 7 We recommend that you retain the bolt in case you remove the front wing sometime in the future. Nut A x1 (already installed in Arrow upper steering clamp) ACTEVMOTORS.COM BODY KIT ASSEMBLY - FRONT WING | 5...
- Page 8 Assemble front wing and front nose using a Phillips screwdriver and 10mm side of the open-end wrench. Nut B Use a large towel spread on a table during assembly to prevent scratches. Leave two tape straps in place during assembly. Screw B x4 Nut B x4 Remove two tape straps after all four screws...
- Page 9 Make sure the front wing cable is resting on top of the frame. Face the front wing as if you were driving the Arrow and tighten the front wing studs in a clockwise direction. Use the 13mm side of the open-end wrench.
- Page 10 Insert Bolt A through the front wing support and upper steering clamp. Locate Nut A that was removed in step 1. Thread Nut A on the other side and tighten with the open-end wrench and screwdriver. Note: Nut will not fit into the steering clamp but rest outside on the metal bracket.
- Page 11 Rear Wing Screw C x4 Right Wing Support Screw D x6 Left Wing Support You will need: Phillips Screwdriver x1 Pop the rear cover off posts on each side of the Arrow. ACTEVMOTORS.COM BODY KIT ASSEMBLY - REAR WING | 9...
- Page 12 Gently pull back on the rear cover. Insert 2x Screw C through each of the side wing supports and into the rear wing and tighten. Note Wing Orientation Note: The side wing supports should be installed so that they bow outward. The wing back edge should bend upward.
- Page 13 BODY KIT - DECALS Insert 3x Screw D through the side wing support and into the rear cover and tighten. Repeat on the other side. Screw D x6 ACTEVMOTORS.COM BODY KIT ASSEMBLY - DECALS | 11...
- Page 14 BODY KIT - DECALS Provided Parts NOTE: Apply rear wing cap before applying the number of your choice. (choose any preferred number) Repeat placement of decals for the other side of the body kit. ACTEVMOTORS.COM BODY KIT ASSEMBLY - DECALS | 12...
Need help?
Do you have a question about the Arrow and is the answer not in the manual?
Questions and answers