Advertisement
Quick Links
Scroller power supply
with optional Wireless DMX
Instruction Manual
Models:
WPSU-600/480/240
version 1.0 since 22 October 2018
DDL4
ATTENTION!
This instruction manual contains important information about the installation and the use of
the equipment. Please read and follow these instructions carefully.
Always ensure that the power to the equipment is disconnected before opening the
equipment or commencing any maintenance work.
WPSU_en_manual_M198
( 1 / 12)
Advertisement
Summary of Contents for SRS Lighting WPSU-600
- Page 1 Scroller power supply with optional Wireless DMX Instruction Manual Models: WPSU-600/480/240 version 1.0 since 22 October 2018 DDL4 ATTENTION! This instruction manual contains important information about the installation and the use of the equipment. Please read and follow these instructions carefully.
-
Page 2: Dmx Connection
IMPORTANT SAFETY INFORMATION The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings in this manual violates safety standards of design, manufacture, and intended use of this equipment. Do not operate in an explosive atmosphere! Do not operate this equipment in the presence of flammable gases or fumes. -
Page 3: Front Panel
Front panel: WPSU600: WPSU480: WPSU240: On the front panel, there is a red POWER indication LED for the power supply state. There is also a DATA LED for DATA indication. DATA LED is ON, when the DMX signal is connected to the device or it is received by the Wireless DMX. Wireless DMX is operated separately from the W-DMX module. -
Page 4: Rear Panel
Rear panel: The MAINS fuse and MAINS connector /Neutrik PowerCon/ are located on the rear side of WPSU. On both long sides of device, there are 4 holes for M6 Eyebolt and 2 holes M10 for C-CLAMP attachment. ( 4 / 12) - Page 5 Device in use: By default, Power LED indicates whether the device is on main power. If the Power LED does not come up, please check mains power input or fuse. Always use fuses of the same rating as the one received from manufacturer or one of rating written on backside.
- Page 6 DMX only operation For the DMX operation, turn off the W- DMX module by holding the MODE button until both W-DMX and MODE buttons turn RED. Now connect the DMX cable to DMX-IN connector and use WPSU as standard DMX Scroller power supply. DMX+ Wireless DMX operation For W-DMX operation, turn ON the W-DMX module by holding the MODE button until...
- Page 7 W-DMX functions 1. W-DMX is turned OFF. WPSU is used as a DMX splitter. To turn the W-DMX ON, hold the MODE button for three seconds. MODE button will light GREEN. 2. W-DMX is ready to be linked, WPSU works as s receiver of W-DMX signal without linking to the transmitter.
-
Page 8: Technical Data
Address of producer: Rybnicna 36/D, 83107 Bratislava, Slovak Republic Declares that the product Name of product: WPSU, Scroller power supply Type: WPSU-240, WPS-480, WPSU-600, PSU-240, PSU-480, PSU-600 Corresponds to the following product specifications and R&TTE Directive of the European Union: Safety: EN60065, resp. - Page 9 ( 9 / 12)
- Page 10 ( 10 / 12)
- Page 11 ( 11 / 12)
- Page 12 Copyright 2018 SRS Group s.r.o. | Specifications subject to change without notice. Document: WPSU_en_manual_M198 | Version 1.0 | Actual as of: 22 October 2018 SRS Group s.r.o. Rybnicna 36/D | 831 07 Bratislava | Slovakia Phone: +421 2 44 681 417 | Fax: +421 2 4468 1419 Email: sales@srs-group.com | www.srs-group.com ( 12 / 12)
Need help?
Do you have a question about the WPSU-600 and is the answer not in the manual?
Questions and answers