Advertisement
Quick Links
Product Installation Guide
Rocker Switch (Single, Double)
1] Description
The light switch, also known as "rocker switch" is a battery free, wireless transmitting device that communicates with a
wide variety of receivers, including relay controllers as well as all of the Magnum OPUS line. Every time the light switch is
pressed, a small micro generator produces a tiny electrical current that powers a built in transmitter. This transmitter sends
wireless signals that command the relay/receiver to turn a device "off", "on" as well as "dimming", where applicable.
2] Package Contents & Tools Required
• Rocker Pad
• Wall Plate
• Power Drill, 3/16" bit
• Screwdriver
3] Features
• User interface for switching, dimming (when used with a dimmable controller) and more.
• Harvests energy from linear motion - no batteries.
• Transmits unique message each time pressed or released.
4] Dimensions
4.95"
125.76mm
.74"
3.21"
18.84mm
81.76mm
5] Technical Specifications
Part Numbers
ESRP = Single Rocker
EDRP = Double Rocker
Power Supply
Integrated Radio Transmitter
Transmission Range
Dimensions
Weight
Environment
Agency Compliance
Magnum Innovations
5675 Hudson Industrial Pkwy, Suite 3
MZ-ESRP / EDRP
• Screws and Wall Anchors
• Leveling Tool
4.95"
125.76mm
.72"
4.52"
18.34mm
114.99mm
MZ-ESRP
MZ-EDRP
Mechanical energy harvesting
(power is generated by the motion of pressing the switch)
Zigbee BLE PTB 215 B
typ. 328 ft (100 m) free field / 32.8 ft (10 m) indoor
Single: 4.95" H x 3.21" W x 0.74" D (126mm x 82mm x 19mm)
Double: 4.95" H x 4.52" W x 0.72" D (126mm x 115mm x 18mm)
Single: 3.9 oz (112g)
Double: 5.3 oz (150g)
• Indoor use only
• 14° to 104°F (-10° to 40°C)
• 20% to 95% relative humidity (non-condensing)
FCC, IC
Hudson, OH 44236
phone 330.915-2382
6] Planning
Take a moment to prepare and ensure optimal communications with other system components, and for user convenience.
• Pick a convenient location, perhaps near a door where occupants enter and exit
• Consider the construction materials in the space and obstacles that may interfere with RF signals
7] Installation
1. Decide where you want to mount the rocker pad. The standard height for wall switches is 49" or 125 cm on center.
2. Remove the wall plate from the rocker pad assembly.
3. Decide which of the two installation options is appropriate.
A. Surface Mounted Installation
i. Using a level and a pencil, lightly mark 2 small dots to align the top edge of the mounting plate.
ii. Mark the mounting screw drill points.
iv. Drill holes for the wall anchors with a 3/16" drill bit and
insert wall anchors.
v. Insert the top screw(s) loosely and level the back plate.
vi. Insert the bottom screw(s), and then hand tighten
the top screw(s).
vii. Attach the wall plate on top of the rocker pad using
the two screw holes.
NOTE: For proper assembly, make sure to align the "top" labels on the rocker pad and wall plate.
B. Flush Mounted Installation
NOTE: When installing over an existing wall box make sure any bare electrical wires are capped.
i. Remove the assembly screws which hold the wall plate, rocker pad, and mounting plate together.
ii. Use a tool to carefully pry the rocker pad free from the back plate. The back plate is not used for this option.
iii. Mount the rocker pad over the existing wall box using the two screw holes,
NOTE: For proper assembly, make sure to align the "top" labels on the rocker pad and wall plate.
iv. Attach the wall plate on top of the rocker pad using the two wall box screw holes.
4. Insert the trim plate tabs in the bottom slots, and then lightly flex the plate to insert top tabs.
TIP: To remove the trim plate, use a flat-head screwdriver to depress the trim plate tabs using the 2 slots on the bottom
of the wall plate. Alternatively, use a fingernail to press down along the top groove and flex the tabs out of the slots.
5. Click the rocker pad on and off to test the mechanism.
NOTE: To activate dimming, press and hold; top button to increase, bottom button to decrease.
fax 330.529.5279
www.magnum-innovations.com
info@magnum-innovations.com
1
Advertisement
Related Manuals for Magnum MZ-ESRP
Summary of Contents for Magnum MZ-ESRP
- Page 1 2. Remove the wall plate from the rocker pad assembly. wide variety of receivers, including relay controllers as well as all of the Magnum OPUS line. Every time the light switch is 3. Decide which of the two installation options is appropriate.
- Page 2 U.S. Two-year Limited Warranty: Products purchased in the U.S.A. are warranted for two years from date of purchase by Magnum Energy Solutions, LLC (M.E.S.) to be free of defects in materials and workmanship. In the event of Part 3: Linking the switch to the compatible system.