Miknetum MPR 1500 1 Safety Instructions !!! Observe the safety instructions during the installation, operation, cleaning and maintenance of the Rühle Miknetum! Hazard potentially causing irreversible injuries if disre- garded. Warning, potentially causing serious injuries if disre- garded. Note Work on electrical equipment of the machine may only...
Page 4
Miknetum MPR 1500 b) Prepare work instructions for the intended and safe transport, commissioning, setup, operation, cleaning, decom- missioning, care / maintenance as well as dismantling / dis- posal! c) Make sure that the qualified workers have completely read and understood the respective work instructions according to section 1.1b!
Page 5
Miknetum MPR 1500 a) Visual check for changes or damages on all machine sides and accessible machine parts, e.g. steel cables and chain. The ma- chine must be shut down in the event of any damages or changes! b) Check the safety switches as follows: –...
Miknetum MPR 1500 !!! Only Rühle spare parts and accessories may be used. !!! The operating instructions as well as all other technical documents included must be supplied completely when reselling the machine. 1.2 Remaining risk of accidents !!! All life cycles phases...
Miknetum MPR 1500 1.3 Intended Use The Miknetum has been solely designed for mixing, salting/season- ing, marinating and tumbling meat products and salads. The max. room temperature may be 12 °C for reasons of food hygiene! This machine is designed for operation by a person ...
Miknetum MPR 1500 2.1 Machine transport and setup Please refer to the short instructions supplied with the machine re- garding transport and setup of the Miknetum. The machine and machine parts must be transported by 2 persons (1x operator of floor conveyor / 1x transport su- pervision).
Miknetum MPR 1500 2.3 Connecting the machine The machine is connected to a three-phase current outlet; its data (voltage, amperage) must agree with the specifications on the type plate of the machine. The machine must be decommissioned until a damaged...
Page 10
Miknetum MPR 1500 If the power fails when a user program is being executed the machine will react as follows when the power supply is reinstated: it will start up again automatically and the program will continue from that point at which it was in- terrupted by the power failure.
Page 11
Miknetum MPR 1500 When emptying the drum corresponding appropriate pre- cautions must be taken to ensure that no person stands in the discharge area of the machine! Make sure when mounting (or adjusting) the tumbling arm, mixing arm (alternative blind plug), standard trolley...
Miknetum MPR 1500 (= discharging position) so that it can be used for any op- erating process. The tablet PC may only be operated by touching it with the fingers. Using any objects (e.g. blade) is prohibited! 4 Cleaning instructions The Miknetum has been designed to allow for complete cleaning of all parts that come into contact with the food product.
Miknetum MPR 1500 Cleaning with high-pressure cleaners is permitted only for: all outside surfaces, drum, lid and lid seals, intake filter and air intake pipe, tumbling arm, mixing arm and blind plug The tablet PC and its holder must be cleaned manually...
Miknetum MPR 1500 4.3 Cleaning procedure Please refer to the short instructions supplied with your machine for carrying out the cleaning procedure. Cleaning preparations: To ensure optimum cleaning, some components of the machine must be removed. Remove the mixing arm and the tumbling arm from the drum! ...
Miknetum MPR 1500 this is only done by qualified personnel! the machine is always disconnected from power! a waiting time of at least 10 minutes is observed af- ter switching off the machine to allow the capaci-...
Miknetum MPR 1500 5.2 Regular maintenance Regular maintenance of the machine must be carried out every 2000 hours of operation but at least once per year. Maintenance schedule: a) Inspect the safety devices as outlined in Chapter 1.1 Safety Instructions!
Miknetum MPR 1500 Lid drive Tumbling arm drive Mixing arm drive Slewing gear Lifting aid drive Vacuum pump Compressor (cooling unit) All gears/motors except for the compressor are equipped with oil draining screws. The compressor must be drilled open for draining the oil.
Miknetum MPR 1500 Measured according to: DIN EN ISO 11201 accuracy class 2 Measured: while idling without product, at maximum speed The data on the type plate principally applies; it is located at the front of the machine next to the main switch. In case of deviations contact...
Miknetum MPR 1500 8 EC Declaration of Conformity according to Directive 2006/42/EC The manufacturer herewith declares that the following product Name: Rühle GmbH Type: MPR 1500 Legal form: Lebensmitteltechnik Address: Beim Signauer Schachen 10 Designation: Miknetum D – 79865 Grafenhausen From series no.:...
Need help?
Do you have a question about the MPR 1500 and is the answer not in the manual?
Questions and answers