Summary of Contents for iMettos HLC-300
- Page 1 Vegetable Cutter Instruction Manual Model: HLC-300 Please read this instruction manual carefully before operating this equipment...
-
Page 2: Table Of Contents
CONTENTS 1.SAFETY 2.INFORMATION ON SAFETIES 3.PERFORMANCE PARAMETER 4.INSTALLATION 5.OPERATION INSTRUCTIONS 6.CLEANING AND MAINTENANCE 7.DISK 8.EXPLODED DRAWING- 1 - 9.CIRCUIT DIAGRAM 10. WASTE DISPOSAL 12. WARRANTY - 1 -... -
Page 3: Safety
1.Safety Tips Read this instruction manual before using and keep them available at all times! • Position on a flat, stable surface. • A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product. •... -
Page 4: Information On Safeties
DIMENSIONS WEIGHT POWER ELECTRICAL REVS WATT CONNECTION DISC HLC-300 57X23X51 22.50 110/1/50~60 220~240/1/50~60 380/1/50~60 3.2. SUPPLY CONDITIONS AND DISPOSAL OF PACKINGS THE CUTTING MACHINE IS PACKED IN A STURDY CARDBOARD BOX WITH INTERNAL SHAPED EDGES WHICH GUARANTEE THE PERFECT INTEGRITY OF THE MACHINE DURING TRANSPORT. -
Page 5: Installation
4. INSTALLATION 4.1. SETTING THE MACHINE THE MACHINE CONNECTION AND THE SETTING AT WORK MUST BE MADE BY SKILLED PERSONNEL. WARNING: BOTH THE SYSTEM AND LOCATION WHERE THE EQUIPMENT HAS TO BE SET MUST COMPLY WITH THE REGULATIONS FOR THE ACCIDENT PREVENTION AND ELECTRICAL REGULATIONS ICE FORCE. THE MANUFACTURER DECLINES ANY AND ALL RESPONSIBILITY FOR DIRECT OR INDIRECT DAMAGES WHICH MAY ENSUE FOR NON-COMPLIANCE WITH THE ABOVE MENTIONED REGULATIONS. - Page 6 COVER OPENING (1) DISC POSITION (2) ATTENTION TO DISC BLADES!! 5.3. SETTING AND CUTTING THE FOOD LIFT THE HANDLE AND SET THE FOOD INSIDE THE OPENING AS SHOWN IN FIGURE N.3, THEN PUT DOWN THE HANDLE, PRESS THE GREEN START BUTTON WITH YOUR RIGHT HAND, AND WITH YOUR LEFT HAND, LIGHTLY MOVE THE HANDLE DOWNWARDS UNTIL FOOD IS FULLY USED UP.
-
Page 7: Cleaning And Maintenance
6. CLEANING AND MAINTENANCE OPERATIONS 6.1. GENERALITIES AND PRODUCTS FOR CLEANING BEFORE CARRYING OUT ANY CLEANING OR MAINTENANCE OPERATIONS, CHECK TO MAKE SURE THAT THE MAINS SWITCH BE OFF AND THE SUPPLY PLUG DISCONNECTED FROM THE MAINS. ACCURATELY CLEAN THE EQUIPMENT AND THE DISCS EVERY DAY FOR A CORRECT OPERATION AND LIFE OF THE EQUIPMENT. - Page 8 3) BY ADJUSTING THE SCREW TO ADJUST THE BELT TENSION 6.3. MACHINE IDLE FOR A LONG TIME SHOULD THE MACHINE BE IDLE FOR A LONG TIME, DISCONNECT THE MAIN WALL SWITCH AND CLEAN THE MACHINE AND ITS ACCESSORIES ACCURATELY. USE WHITE VASELINE OIL (OR SIMILAR PRODUCTS) TO PROTECT ALL THE MACHINE’S ELEMENTS.
- Page 9 HU2.5 HU4 HU8 HU10 D8 D10 D12 D20 T8 T10 COMPOSE H8 H10 D10 D12 D20 D8 D10 D12 D20 COMPOSE H8 T8 H8 T10 H10 T8 H10 T10 - 8 -...
- Page 10 8. EXPLODED DRAWING - 9 -...
- Page 11 9. ELECTRICAL DRAWING - 10 -...
-
Page 12: Waste Disposal
11.Warranty iMettos warrants to the original purchaser of every new product, under normal and proper use and maintenance service as specified by iMettos and upon proper installation and start-up in accordance with the instruction packet supplied with each unit. iMettos’... - Page 13 Limited www.imettos.co.uk - 12 -...