Trinkwassertafel Overview Overview Structure Fig. 1-1 Overview of drinking water panel (example) A mounted drinking water panel that is ready for operation consists - depending on the order - of the following main components (Fig. 1-1): Ready-mounted baseplate with: – monitor, designed for the measured parameter (pos. 1) –...
Trinkwassertafel Safety instructions Safety instructions This chapter contains essential instructions that must be followed during the commissioning, operation and maintenance of the drinking water panel. Thus, it is essential for the operator to read this component operating manual before carrying out any work with the system. Some components (monitor, sensor) are delivered with their own operating manual.
Safety instructions Trinkwassertafel Special user The following installation activities may only be performed by a qualifications qualified electrician: Connecting the drinking water panel to the supply line (see operating manual of the monitor). Connection of external, line voltage-carrying circuits to relay contacts (see operating manual of the monitor).
Page 9
Trinkwassertafel Safety instructions Safe operation If safe operation is no longer possible, the drinking water panel must be taken out of operation and secured against inadvertent operation. Safe operation is no longer possible if components: have been damaged in transport have been stored under adverse conditions for a prolonged period of time are visibly damaged...
Trinkwassertafel Installation Installation Installation prerequisites Requirements of the The drinking water panel is intended for mounting on a flat, vertical wall. measurement location The measurement location must meet the environmental conditions specified in chapter 5 T . Make sure there is good ECHNICAL DATA accessibility for maintenance and setting work.
Installation Trinkwassertafel Wall mounting The base plate has four holes at the corners for attaching to a wall. Make sure the wall has the necessary stability for the weight of the drinking water panel. Only use mounting material which is suitable for the wall material (screws, dowels, etc.).
Trinkwassertafel Installation Connecting the voltage supply The monitor of the drinking water panel is supplied with mains voltage. The mains voltage must comply with the specifications given on the nameplate and in the operating manual of the monitor. The power line and all lines to current outputs and relays can be laid via the two openings at the back of the base plate.
Installation Trinkwassertafel Installation of the sensors Note Heed the instructions for installation in the sensor operating manual. Installation in the Install the sensor in the flow-through vessel. Depending on the drinking water panel type, the sensor is screwed into the installation opening up to the stop or plugged in and then fixed with a coupling ring.
Page 15
Trinkwassertafel Installation Wiring diagram Fig. 3-2 Wiring diagram for the sample flow monitoring Note Set the current range of the output ideally between 4 and 20 mA in order to reliably detect any decrease in sample flow to below the switching threshold even at low measured values.
Installation Trinkwassertafel Commissioning To commission the drinking water panel, proceed as follows: Switch on the supply voltage for the monitor and wait until the monitor has started up. Make the necessary settings on the monitor (see operating manual of the monitor). Open the sample inlet and adjust the sample flow (for values, see chapter 5 T ECHNICAL DATA...
Trinkwassertafel Maintenance and cleaning Maintenance and cleaning Maintenance Maintenance activities Component Maintenance Pipe system Regularly check all joints for traces of escaping water (visual control) Monitor (see monitor operating manual) Sensors Depending on the sensor type (see sensor operating manual) Other components See component operating manual Cleaning...
Page 18
Maintenance and cleaning Trinkwassertafel Contamination Cleaning agents Implementation Algae, biofilm Water and household – Dismantle pipe washing-up liquid system – Clean innner surfaces with brush/cloth and washing-up liquid – Subsequently rinse thoroughly with water (carefully remove any residues of washing-up liquid!).
Trinkwassertafel Technical data Technical data Wall mounting panel Dimensions (H x W x D) Approx. 1100 x 350 x 13 mm Clearance to the wall 20 mm via rear spacer bolts on the plate Material PVC rigid foam, spumed, white Mounting Through four drillings in the panel, diameter 8.5 mm, drilled hole diagram, see Fig.
Page 20
Technical data Trinkwassertafel ba75752e01 08/2008...
108 105 ORP buffer solution, pH 7, RH 28 109 740 UH=427mV (CH), 250 mL (Buffer solutions in larger trading units are listed in the WTW catalog or on the Internet) Oxi 4000 (oxygen) drinking water panel Description Model Order...
AK-CL 108 152 sensors, 1 m Note Photometer for calibration of the chlorine sensors and photometric test kits are given in the WTW catalog or on the Internet at www.WTW.com. General replacement and accessory parts Description Model Order Pressure regulator R1/2"...