Newall Spherosyn 300 Quick Install Manual

Newall Measurement Systems Ltd.
Technology Gateway, Cornwall Road South
Wigston, Leicester LE18 4XH
Tel: +44 (0) 116 264 2730
sales@newall.co.uk
www.newall.co.uk
Newall Electronics Inc.
Tel: +1 614 771 0213
CHINA & TAIWAN
Sensata Technologies China Co., Ltd
People's Republic of China
Tel: +86 212 2306 1500
SINGAPORE & KOREA
Sensata Technologies Co., Ltd
Tel: +65 647 86 867
Sensata Technologies Japan Ltd.
Tel: +81 45 277 7120
More information at sales@newall.com • www.newall.com
Part No: 023-?????-UK
EUROPE
United Kingdom
AMERICAS
USA
Singapore
JAPAN
Japan
Spherosyn & Microsyn 300 Quick Install
For the complete manual please download from:
http://newall.com/nms300
Preparation
Prior to beginning the installation the machine should be studied to determine the Encoder(s) position and to
ensure the brackets are suitable, or if custom brackets are required.
In order to reduce erroneous readings caused by machine wear it is recommended that the encoder be fitted as
close to the machine lead screw or axial drive shaft as possible.
Warnings
If for any reason the machine axis travel is greater than the actual scale travel, 'mechanical stops' should be
fitted to the machine to avoid damage caused by over-travel. Newall will not accept responsibility for encoder
damage caused by machine over-travel.
It is important the Scale be kept at least 13mm (0.5") away from any magnetic sources such as magnetic bases
or chucks.
Assembly Diagrams
SIZE DRAWING 31687934 REV.
A3 NUMBER ISS.
Figure 1 - Spherosyn300 Encoder Assembly
8
7
M8
9
5
10
6
1. Spherosyn300 reader head (1)
2. Spherosyn300 scale (1)
3. Scale support link (2)
4. Scale anchor pin (2)
5. Support pillar short (2)
Serial Number
& Accuracy
Mark End
Figure 2 - Microsyn300 Encoder Assembly
15
M6 5
4
11
8
9
14
13
1. Microsyn300 reader head (1)
12
2. Microsyn300 scale (1)
REV.ISS. DATE C.N.No ALTERATION
3. End support mounting (1)
4. M3 x 16 SHCS (1)
5. M3 spring washer (1)
6. Support mounting (1)
7. M4 x 5 nylon set screw (1)
8. Support link (2)
DO NOT SCALE
2
1
6. Support pillar long (2)
7. Scale cover (1)
8. M5 x 20 hex head (6)
9. M8 socket button head (2)
10. Spacer washer (2)
1
3
10
MATERIAL/FINISH
TITLE
9. M3 x 12 hex screw (4)
DRAWN
chris.wh
10. M3 x 12 SHCS (4)
DATE 09/02/2017 THE INFORMATION THERON MAY NOT BE COPIED OR USED
Leicester England
11. M6 x 10 socket button head (2)
12. Support pin short (2)
13. Support pin long (2)
14. Spacer washer (2)
15. Scale cover (1)
Guide
THIRD ANGLE PROJECTION IF IN DOUBT ASK
3
4
6 7
2
SCALE
UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES  0.5
STATED: - 1 DECIMAL PLACES  0.2
2 DECIMAL PLACES  0.1
ANGULAR  1 
DIMENSIONS ARE IN M.M
31687934
THIS DRAWING IS THE PROPERTY OF SHEET DRAWING REV.
NEWALL MEASUREMENT SYSTEMS LTD.
1 OF 1
NUMBER ISS.
WITHOUT WRITTEN PERMISSION