Page 1
Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit. For an Operator’s Manual and Decal Kit in French Language, please see your Land Pride dealer. Printed 1/30/19...
Page 4
Download the appropriate App on your Refer to Parts Manual QR smart phone, open the App, point your Locator on this page for phone on the QR code and take a picture. detailed instructions. BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M 1/30/19...
Important Safety Information Important Safety Information Listed below are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look for the Safety Alert Symbol Careful operation is your best The SAFETY ALERT SYMBOL indicates there is a assurance against an accident.
Page 6
Lower attachment to the ground and Replace parts on this attachment trained personnel using the follow all shutdown procedures with genuine Land Pride parts only. correct tools and equipment. before leaving the operator’s seat to Do not alter this attachment in a way ...
Page 7
Use Seat Belt and ROPS signals are recommended Keep Riders Off whenever driving on public roads. Machinery Land Pride recommends the use of a CAB or roll-over-protective- Never carry riders on the power structures (ROPS) and seat belt machine or attachment.
Spray soapy water onto the cleaned area. all damaged or missing labels. Order new labels from your Peel backing from label and press label firmly onto the nearest Land Pride dealer. To find your nearest dealer, surface. visit our dealer locator at www.landpride.com.
Universal Quick Attach type hitch plate with a location of your serial number plate, see Figure 1. single spear on the BS10 and dual spears on the BS20. The BSE10 & BSE20 models are designed to fit Euro type hitch plate with a single spear on the BSE10 and dual spears on the BSE20.
Installation full inside length of spike mounting tubes (#7). The BS10 & BS20 Bale Spears are designed to fit on Skid 5. Rotate bale spikes (#3) so that the flat surfaces (#8) Steer style hitch plates and BSE10 and BSE20 are are facing up.
3. Rotate top of skid steer tilt arms slightly forward. Push lock handles on Skid Steer style hitch plate down so that the pins go through the bottom slots of the Bale Spear hitch plate and handles lock down. 1/30/19 BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M...
Check Bale Spear frequently to make sure it is properly • attached and locking pins are properly seated. BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M 1/30/19...
Always transport with bale raised to a height that does not hinder the line of sight going forward. When possible, keep the bale low to the ground to help maintain stability of the tractor/skid steer. 1/30/19 BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M...
Make sure spear(s) clear the bale before turning or changing height of spear(s). 8. Lower spear down to transport height before moving again. BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M 1/30/19...
3. Repaint parts where paint is worn or scratched to Perform scheduled maintenance. Check for loose • prevent rust. Ask your Land Pride dealer for aerosol hardware, missing parts, broken parts, structural cracks, touch-up paint. They are also available in touch-up and excessive wear.
Also, two spears do a better job bales of stabilizing the load. Double spear units probe lower on They can lift the bale higher. the bale BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M 1/30/19...
Traveling forward while going down an tip forward. incline with a slope in excess of 10 Back down steep inclines. percent. Bale does not carry level One of two spears is bent. Replace bent spear. 1/30/19 BS10, BS20, BSE10, & BSE20 Bale Spears 319-062M...
This Warranty is limited to the repair or replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
Need help?
Do you have a question about the BS10 and is the answer not in the manual?
Questions and answers