For components.
guard-locking mechanism (16 pages)
Summary of Contents for Haake HST-TZ1
Page 1
Translation of Original Manual HST-TZ1 Ident.-No.: 10234 HST-TZ1 Ident.-No.: 10236 HST-TZ1 Ident.-No.: 10235 HST-TZ1 Ident.-No.: 10237 HST-TZ1, pictured Ident-No. 10234 and 10237 The image may differ from the product. Read the operating manual before beginning any work! Haake Technik GmbH Master Esch 72 48691 Vreden, Germany info@haake-technik.com...
No parts of this documentation may be reproduced or transferred in any manner or by any means, be it electronic or mechanical, for any purpose without obtaining prior written consent. Haake Technik GmbH assumes no liability for damage or subsequent damage, arising from the use of components or replacement parts, which are not original parts.
Info@haake-technik.com Intended use The Guard-locking mechanism HST-TZ1 with an adjacent Actuator serves as access protection and can be used on separating safeguards such as swing doors and sliding doors or flaps. The Actuator can be removed by operating the HST-TZ1, whereby the safeguard can be opened.
In rear access safeguards it cannot be excluded that a person will be in the dan- ger area when the safeguard is closed and guard-locking by the HST-TZ1 is ef- fective. For such cases, a Guard-locking mechanism with a second key (personal key) is to be used.
Fault exclusions Due to the construction, materials, and components used for the component, the faults listed in the table can be excluded: Potential Fault Exclusion of Fault Limitations of Use Reason Wear, corrosion. Permissible acc. See sections 2 Use of carefully select- Intended use and tables A.4 and A.5 of ed materials and man-...
Scope of delivery 1 x Guard-locking mechanism HST-TZ1 consisting of a casing with a Blocking mechanism, an inte- grated lock and an adjacent actuator (actuator interlocked in protection position). Actuator Casing with a Blocking mechanism and lock. Figure shows HST-TZ1 Ident.-No.: 10234...
Actuator. To remove the Actuator the coded key is inserted and turned in the lock. The Actuator can then be turned and removed. The Guard-locking mechanism HST-TZ1 ensures that the safeguard cannot be opened before the key is inserted and turned, when the safeguard is closed and the Actuator is locked.
Do not make any alterations to the component. Otherwise, this could lead to malfunctions, which can cause serious personal injury and irreparable damage to property. In the event of non-compliance, the guarantee is invalidated and Haake Technik GmbH does not ac- cept any liability.
Installing the component requires the following items that are not included in the scope of the delivery: HST-TZ1 Ident.-No.: 10234 and HST-TZ1 Ident.-No.: 10235: 2 screws M8 x “length of relevant installation site“ from A2-70 ...
13 Performance check Attention! The protective effectiveness of the compo- nent must be checked regularly - at least once a year - in intervals according to national operat- ing instructions Once installed, do not loosen any bolts or nuts or remove any pins; otherwise, the effectiveness of the safety-related func- tions is no longer guaranteed.
Only uninstall the component when power to the electrical system is switched off. Loosen the attachment of the HST-TZ1 depending on the version. 1. Loosen the fastening screws of the casing with the blocking mechanism. 2. Loosen the alternative fastening selected by you (e.g. riveting, safety screws by drilling them...
Key inserted incorrectly. Remove the key and if neces- sary insert it rotated 180°. Mechanical fault. Contact Haake Technik GmbH. Actuator cannot be removed. Key is not turned to the stop at Turn the key until the stop. the end position.
20 Dimensions Dimensional specifications in mm. HST-TZ1 Ident.-No.: 10234 Description: The release key cannot be retracted. Release key not included. HST-TZ1 Ident.-No.: 10235 Description: The release key cannot be retracted. Release key not included.
Page 14
HST-TZ1 Ident.-No.: 10236 Description: The release key cannot be retracted. Release key not included. HST-TZ1 Ident.-No.: 10237 Description: The release key cannot be retracted. Release key not included.