Download
Share
Print this page
Emerson HPR12K-00 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Storage
  5. HPR12K-00
  6. Operating instructions manual
Emerson HPR12K-00 Operating Instructions Manual

Emerson HPR12K-00 Operating Instructions Manual

Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual

Operating Instructions

HPR12K-00
1. General Install
Connecting the input power cable, output load cable and communication wire according
to the below figure.
Aux. DC
Output
AC INPUT
I2C/PMBus
Communication

2. General Settings

Unless otherwise specified, when the PSON# switch is de-asserted (48V o/p is disabled).
It is means Manual ON/OFF DIP switch SW1 should be default according to below table.
And It must be checked before shipping.
PSU 1#
Power Supplies
Status
CH 1
OFF
Up
Note 1. The status Down means set to ON position. The status UP means set to OFF position.
Note 2. Programming Switch SW1 default settings:
PSON switches : OFF
PSKILL switches : ON
AC INPUT
Main DC Output
Main DC Output
AC Line Input
DIP switch SW1 setting as a default
PSU 2#
CH 2
CH 3
CH 4
Down
Up
Down
Embedded Power for
Business-Critical Continuity
AC INPUT
AC INPUT
PSU 3#
PSU 4#
CH 5
CH 6
CH 7
Up
Down
Up
Rev.06.09.10
HPR12K-00
1 of 6
CH8
Down

Advertisement

loading

Related Manuals for Emerson HPR12K-00

Summary of Contents for Emerson HPR12K-00

  • Page 1: Operating Instructions

    Operating Instructions Embedded Power for Business-Critical Continuity Rev.06.09.10 HPR12K-00 HPR12K-00 1 of 6 1. General Install Connecting the input power cable, output load cable and communication wire according to the below figure. Aux. DC Output AC INPUT AC INPUT AC INPUT...
  • Page 2 Technical Reference Note Embedded Power for Business-Critical Continuity Rev.06.09.10 HPR12K-00 2 of 6 3. ON/OFF Operation (PSON#) 3.1 Manual ON/OFF Operation The DIP switch SW1 used turn on or off the PSU by manually. The PSU in SLOT1 is turn on when the CH1 of DIP switch SW1 turn on.

  • Page 3: Remote On/Off

    Embedded Power for Business-Critical Continuity Rev.06.09.10 HPR12K-00 3 of 6 3.2 Remote ON/OFF The per PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +48VDC power rail. When this signal is not pulled low by the system, or left open, the +48VDC output turns off.
  • Page 4 Embedded Power for Business-Critical Continuity Rev.06.09.10 HPR12K-00 4 of 6 5. Connector Define for I/O 5.1 Main Output Connection Table 3 Main Output Connection Definition Designation Identification Terminal Type +48Vdc MAIN OUTPUT Ring Lug, M6 screw +48V_RTN MAIN OUTPUT RETURN...
  • Page 5 Embedded Power for Business-Critical Continuity Rev.06.09.10 HPR12K-00 5 of 6 5.4 Signal Output Connector CN3 Table 8 Signal Output Connector Mating Connector Self Connector Molex: 52986-2679 Tyco: 2-5175677-4 (Astec P/N: 13870011610) Figure 5: Connector CN3 Table 7 Output Connection Definitions foe 5V Standby...
  • Page 6 @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims Table 11 Input Connection and Mating Terminal all liability for damages resulting from use of this information or for any errors or omissions.