Advertisement
2. Press the "+" or "-" button to set the
desired OFF day of the week program.
You can select each day individually,
Monday to Friday, Saturday/Sunday, or
an entire week to have your timer turn
on at dusk and off at the set time.
3. Press the "SET" button to enter the
OFF time hour setting. Press the "+" or
"-" buttons to set time. Be sure to cycle
through until AM or PM appears correctly.
4. Press the "SET" button to enter the OFF time minutes setting.
Press the "+" or "-" buttons to set time.
5. You can press the "SET" button to enter additional programs, up to
8 off program settings. While setting the programs, press and hold
the "SET" button to clear the set program time. Press the "TIME"
button or wait for 15 seconds to store the program, and return back
to the standby display.
HELPFUL TIPS
Do not attach a device that exceeds the unit ratings as described in the
Safety Information section of this manual.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
SPECIFICATIONS:
14/3 AWG SJTW vinyl cord
RATINGS:
125 V ac 60 Hz, 15 A Resistive,
15 A General Use, 1000 W Tungsten,
500 VA Electronic Ballast, 1/2HP.
120 V ac 60 Hz, 8.3 A Ballast.
WARNING
SUITABLE FOR USE WITH OUTDOOR APPLIANCES – RAINTIGHT
WHEN MOUNTED VERTICALLY WITH THE RECEPTACLE FACING
DOWNWARD. NOT FOR WATER IMMERSION.
This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
CARE AND MAINTENANCE
• Store indoors in dry location.
• Always unplug when not in use.
• Do not unplug by pulling on cord.
Back
TROUBLESHOOTING
7-1
PROBLEM
Lights do not
turn on at dusk.
Lights do not
turn on, even
when timer is in
"ON" position.
Lights are
flashing (turning
on and off).
POSSIBLE
CORRECTIVE
CAUSE
ACTION
Timer is not in a good
Move the timer to another
area for light meter to
location where there is no
function as there is too
ambient light.
much ambient light to
detect darkness.
Lights are not in "ON"
Be sure that lights are
position, lights are not
functional by plugging
functioning, or timer is
them directly into the
not receiving power.
outlet. Be sure that lights
are in "ON" position if they
have their own switch. Be
sure that timer is receiving
power - the LED should
light up when plugged
into an outlet and put in
the "ON" position.
The timer is in Dusk to
Move the lights away from
Dawn mode, and the
the timer, or reposition the
light from the
timer so that it does not
plugged-in lights is
face the lights.
affecting the light
sensor.
MADE IN CHINA
Advertisement
