Download Print this page
Sealey AB931.V2 Instructions
Sealey AB931.V2 Instructions

Sealey AB931.V2 Instructions

Air brush kit without propellant

Advertisement

Quick Links

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according
to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE
TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations
are adhered to when using tools.
Ensure that the air brush and accessories are in a clean, sound condition and good working order. Take
action for immediate repair or replacement of damaged parts. Use recommended parts only. The use of
unauthorised parts may be dangerous and will invalidate the warranty.
Ensure the air brush supply hose is not tangled, twisted or pinched.
DO NOT use air brush or accessories if damaged.
DO NOT operate air brush under the influence of drugs, alcohol, intoxicating medication, or if fatigued.
DO NOT direct spray against yourself, other persons or animals, electrical equipment or the machine itself.
DO NOT use the air brush for a task it is not designed to perform.
Wear approved eye protection and a suitable respirator when painting. A full range of personal safety
equipment is available from your Sealey Dealer.
DO NOT allow smoking or open flame in the work area.
2. INTRODUCTION
Gravity fed air brush with composite body. Suitable for blowing-in small areas of panel. Kit includes gravity cup,
propellant adaptor, 1.5mtr of small bore hose, 1/4" reduction nipple. Supplied in composite case.
3. ASSEMBLY
Note: Numbers in brackets refer to item numbers
in Fig. 4.
3.1. Screw the gravity cup (03) into the top of
the nozzle seat (01).
3.2. Screw one end of the hose assembly (05)
onto the inlet (01).
3.3. Screw the other end of the hose assembly
(01) to the air supply.
3.4. When using a compressor (Sealey Model
No. AB900), connect the hose assembly
(05) to the air hose adaptor before
connecting to the compressor, fig.1.A.
3.5. When using a propellant can (Sealey Model
No. AB/P), connect the hose assembly (05)
to the air regulator valve (02).
3.6. Ensure the valve is turned fully anti-clockwise before screwing to the top of the propellant can, fig.1.B.
4 . OPERATING INSTRUCTIONS
4.1. Mask the area which is NOT to be painted.
4.2. Ensure the object to be painted is free from dust, grease and the surface has been prepared.
4.3. After mixing and thinning the paint, as instructed by the paint manufacturer, fill the gravity cup just over
half full and replace the lid.
Note: Mix thoroughly, making sure that the paint is free from lumps. It may be necessary to strain the paint first.
4.4. Turn the air ON and test your spray on a suitable test panel to get the "feel" of your air brush.
4.5. Make any necessary spray adjustments. The paint flow and spray pattern are adjusted by turning the fluid
cap at the front of the air brush. The cap is completely closed when it has been turned clockwise to the
stop point. To obtain various degrees of paint flow, turn the cap anti-clockwise. The maximum flow will be
attained by turning the cap approximately 4 turns anti-clockwise.
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR BRUSH KIT WITHOUT
PROPELLANT
MODEL N
AB931.V2
O:
Fig.1A
Original Language Version
Fig.1B
AB931.V2 Issue: 1 10/01/14

Advertisement

loading

Summary of Contents for Sealey AB931.V2

  • Page 1 MODEL N AB931.V2 Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
  • Page 2 5.4. Clean the needle, fluid cap and air tip with a small piece of cotton wool dipped in thinners. 5.5. Re-assemble the air brush by reversing the above instruction. Original Language Version AB931.V2 Issue: 1 10/01/14 © Jack Sealey Limited...
  • Page 3 WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions, call us on 01284 757525 and leave your full name and address including your postcode. Sole UK Distributor, Sealey Group, 01284 757500 www.sealey.co.uk...