Advertisement
Quick Links
Support Document
__________________________
IntelliBar Net100 Series Printers
Macintosh OS X Network Setup Guide
IntelliTech International, Inc.
43 Broad Street, Section B404
Hudson, MA 01749-2557
TEL: (978) 212-7200
FAX: (978) 562-5678
www.intellitech-intl.com
support@intellitech-intl.com
Advertisement
Related Manuals for IntelliTech IntelliBar Net100 Series
Summary of Contents for IntelliTech IntelliBar Net100 Series
- Page 1 Support Document __________________________ IntelliBar Net100 Series Printers Macintosh OS X Network Setup Guide IntelliTech International, Inc. 43 Broad Street, Section B404 Hudson, MA 01749-2557 TEL: (978) 212-7200 FAX: (978) 562-5678 www.intellitech-intl.com support@intellitech-intl.com...
- Page 2 INTELLITECH INTERNATIONAL, INC. SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF THIS PRODUCT FOR A PARTICULAR PURPOSE. INTELLITECH INTERNATIONAL shall not be liable for any errors contained in this manual or for any damages resulting from loss of use, data profits, or any incidental or consequential damages arising from the use of INTELLITECH INTERNATIONAL products or services.
- Page 3 (“Net 100”) printers in a Macintosh OS 10.5.2 and later network. For more detailed instructions about other IntelliBar Net100 printer configurations refer to the IntelliBar User’s Guide located on the CD-ROM supplied with your Net100 printer or go to the IntelliTech International, Inc. web site, http://www.intellitech- intl.com/index.asp?page=techsupp/techdocs/newuserguide.asp.
- Page 4 (pacemakers, hearing aids, etc.) regarding any restrictions on the use of 802.11x wireless technology. IntelliTech International, Inc. cannot be responsible for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product. Declaration of Conformity (CE)
- Page 5 IntelliBar Net100 Series Printers –Macintosh OS X Setup Guide Introduction This document provides instructions for installing IntelliBar Net100 Series printers in a Macintosh OS X computer system network. IntelliBar Net100 printers are required for use with Macintosh computer networks. NOTE: IntelliBar Standard Series printers are not compatible with Macintosh computer networks.
- Page 6 C. After the printer powers up the control panel display will read ONLINE READY. Once this message is displayed, print a print server status report by pushing the test-print/reset- default button on the back of the printer. CAUTION: Pressing the button for five seconds or longer will reset the print server settings to factory defaults.
- Page 7 3. Install the IntelliBar Mac OS X Printer Drivers A. Download the IntelliBar printer Macintosh drivers from the IntelliTech web site, or locate them in the CD-ROM provided with your printer in the IntelliBar Mac Driver Folder. IntelliBar Mac OS X Driver pkg B.
- Page 8 D. Click on the “Continue” button to install the driver. Your system may prompt you to enter a password in order to continue the installation. If you are prompted for a password and do not know what the password is, contact your system administrator for assistance.
- Page 9 G. To install a new printer, click on “System Preferences” H. In the “Systems Preferences” window, click Printer & Fax In the “Printer & Fax” window, click on the “+” symbol under the blank box on the left side of the window above to add a new printer.
- Page 10 Refer to the print server status report you printed earlier. Type the IP address in the report into the Address Window as shown below. The IP address “192.168.0.103” is used only as an example in this illustration. K. Click the “Add” button. L.
- Page 11 N. The “Print Using:” window will open. Click on the up/down arrows in blue on the right side of the “Print Using” line. O. Click on “Select a driver to use …” line as shown below. P. Scroll down the list and click to highlight your IntelliBar Printer Model, then click the OK button.
- Page 12 Q. The printer that you selected will appear in the Print Using: window. Click the OK button. R. If the IntelliBar driver is correctly installed, the following window will appear under the Print and Fax icon. S. The installation of the IntelliBar printer and its driver is now complete 4.
- Page 13 III. The browser will connect to the Net100 embedded web server and the “Printer Status” page window will open. Click on the “ Update Status” link. The “Network Configuration Login” page will open. You will be prompted to enter a password.
- Page 14 B. Click on the “TCP/IP” link on the left side of the Printer Status page, which will open the “Configure TCP/IP” page. C. In the “Configure TCP/IP” window, “IP Address” block enter the desired IP Address, Subnet Mask and Gateway information. Note: If the IP address you enter here is different than the IP address you used in Step 3.M.
- Page 15 D. Set Boot Method. The default Boot Method is set to “Auto.” From the drop down menu you may select alternate boot methods: Auto, Bootp, DHCP, Rarp, Static. Choose the method you prefer. NOTE: If you wish to retain the same IP address, subnet mask and gateway address, choose “Static.”...
- Page 16 F. Set Keep Alive. Scroll click on the Keepalive Timer setting. The default setting is set to zero (0) minutes. Change the setting to “1.” Changing the setting to 1 enables the printer to send a notification of its presence on the network once every minute, which prevents the printer from becoming “lost”...
- Page 17 H. If you settings have successfully changed the printer configuration you will see the following message: "Configuration has been modified. The unit must be reset for new values to take effect. Data updated successfully." Confirm Settings Changes. Click on the Admin button on the left side of the Printer Status Page.
- Page 18 *** END OF DOCUMENT ***...