Current CP16A0402_02 Quick User Manual

For additional help during Remote Control programming and set up, visit www.currentproductscorp.com/support, where you can read our other support
materials or view our instructional videos. Or, you can reach our customer service department at 850-435-4994.
The optional remote control provides the user with added functionality for
controlling their blinds. The remote control contains single push ability to
move the slats open, closed, or to your favorite position. The remote also
allows the user to set up separate channels to control specified blinds for
Tilt Up/ Left
Tilt Down/ Right
Channel Selector
PAIRING THE REMOTE
Pairing to the remote can be performed before or after installation and
Determine which blind(s) you wish to pair to the handheld remote.
programming of the SMART WAND™.
Press the PROGRAMMING BUTTON
SMART WAND™ you wish to pair to the remote
until you hear a SINGLE BEEP (1) [Fig. 1], then
release.
Press the CHANNEL button until the LEDs reflect
the desired channel you wish to set [Fig. 2].
Use a tack or pen to press and release the PAIRING
button on the back of the remote [Fig. 3] When
this button has been pressed, the LED's on the
front of the remote will scroll to confirm.
To PAIR, press the top left button on the tilt toggle [Fig. 4]. The blind(s) will
jog down and up showing that it has received the command and completed
the process. If you ever need to unpair, you can repeat the same steps and
press the bottom button on the tilt toggle to unpair [Fig. 5].
CH CH
1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5
Figure 4; Push To Pair

REMOTE CONTROL

Quick USER GUIDE
customized control.
Full Up/ Left
Full Open
Full Down/ Right
Favorite
CH CH
Channel LEDs
1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5

SETTING UP THE REMOTE

on each
Figure 1;
Push and Hold
CH CH
1 1 1 1 2 2 2 2 3 3 3 3
Figure 2; Push Channel
Button
Figure 3; Press in Tack
CH CH
1 1 1 1 2 2 2 2 3 3 3 3
Figure 5; Push to Unpair
Briefly press and release to move the slats in the open or closed direction
and stop at the next position setting. There are seven (7) position settings
from the full up to the full down position. The user may also press and hold
the toggle button until the slats get to the desired position, then release the
Moves the slats to the full up position for horizontal blinds or full right
Moves all slats to the full down position for horizontal blinds, or full left
The user can program this button to any position they choose to be their
most preferred position; however, if left unchanged it will move the slats to
approximately half way between the full open and the full down/ left position.
Used to customize control of multiple blinds on a single remote. The currently
selected channel is indicated by the Channel LEDs. Pressing the CHANNEL
Button once will display the current channel. Pressing it again will switch to
the next channel. When all LEDs are lit, the remote is selected to broadcast
The FAVORITE Button allows the user to program a slat position unique to
the user which moves all slats included on that channel to the user's favorite
position.
To program the FAVORITE Button, twist the SMART
WAND™ until the desired position is reached.
Next, press and hold the PROGRAMMING BUTTON
the SMART WAND™ until you hear a TRIPLE BEEP (3),
then release. [Fig. 6].
Your FAVORITE Button is now programmed to move that
blind to your favorite position. Each SMART WAND™ can
be set to have different favorite positions.
After the SMART WAND™ is set, test by moving your
blinds, then pressing the FAVORITE Button. All blinds on
that channel should move to their programmed favorite
position.
4 4 4 4 5 5 5 5
The SMART WAND Remote is powered using (1) 3V 2032 coin cell lithium
battery.
To replace the battery, use a small flat head screwdriver to gently pry the
back off of the remote body.
Once removed, the coin cell battery should be visable. Slide the coin cell
battery down until it comes out of the battery holster. Inset the new battery
by sliding it up into the battery holster.
Replace the remote backing.
4 4 4 4 5 5 5 5
REMOTE BUTTON DESCRIPTIONS
TILT TOGGLE
toggle.
FULL UP/ LEFT
position for vertical blinds.
Moves all slats to the full open position.
FULL OPEN
FULL DOWN/ RIGHT
position for vertical blinds.
FAVORITE
CHANNEL SELECTOR
on all channels.
SETTING THE FAVORITE BUTTON

Changing the Batteries

on
Figure 6; Push
and Hold
Programming
Button
1995 Hollywood Ave.
Pensacola, FL 32505
850-435-4994