Summary of Contents for Magnum 5012MAG-42VM
- Page 1 Magnum Gas Powered, Diesel Heated, V-Belt Drive Skid Instructions for use DOC0019 REV A...
-
Page 2: Table Of Contents
Contents Important safety instructions .......................4 Description .............................5 2.1 Purpose ............................5 Before starting the machine......................6 3.1 Fuel and air mixture ........................6 3.2 Fill up fuel tank .........................6 3.3 Connecting the high pressure hose ..................6 3.4 Connecting the water supply ....................6 Control / Operation ........................7 4.1 Connections..........................7 4.2 Switching on the cleaner ......................7 4.3 Using cleaning agents ......................7... -
Page 3: Important Safety Instructions
Symbols used to mark in- Safety instructions This indicates structions in these operat- tips and in- ing instructions structions to sim- Before using the which must be plify work and to high-pressure observed to ensure safe operation. cleaner, be sure prevent risks to persons are to also read the marked with this danger symbol. -
Page 4: Description
2 Description Purpose This high-pressure cleaner has etc. been designed for professional use in Section 5 describes the use of the high-pressure cleaner for - Agriculture various cleaning jobs. - Industry - Transport industry Always use the cleaner as - Automotive described in these operating - Municipal Facilities instructions. -
Page 5: Before Starting The Machine
3 Before starting the machine Fuel and air mixture Every fuel-burning appliance, such as pressure washers, depends upon a proper mix of fuel and air (by weight) for proper combustion. Therefore some adjustment of the air supply to the burner may be necessary to take account and the resulting air pressure. This is true whether your fuel is ‘Natural gas’, Propane or Diesel. -
Page 6: Control / Operation
4 Control / Operation Connections 4.1.1 Connecting the spray nozzle to wand Insert spray nozzle into wand quick connect. NOTE! Always remove any dirt from the nipple before connecting the nozzle to the spray gun. Switching on the cleaner 4.2.1 Cold water operation Before starting up the engine, you must carefully read through the instructions for use of the... -
Page 7: Applications And Methods
5 Applications and methods Techniques Effi cient high pressure cleaning is achieved by following a few guidelines, combined with your own personal experience of specifi c cleaning tasks. Accessories and detergents, when correctly chosen, can increase the effi ciency of your pressure washer. Here is some basic information about cleaning. -
Page 8: Some Typical Cleaning Tasks
Some typical cleaning tasks 5.2.1 Agriculture Task Accessories Method Stables Chemical Foam Soaking – apply foam to all surfaces (bottom to top) Pig Pens, Sties Injectors and wait for approx. 30 minutes. Remove the dirt from surfaces with the high pres- Cleaning of walls, Foam lance sure lance or chosen accessory. - Page 9 5.2.3 Buildings and Equipment Task Accessories Method General surfaces Foam injectors 1. Apply thick foam over the surfaces to be cleaned. Standard lance Apply on dry surfaces. Apply from top to bottom on Tank cleaning Metallic equipment vertical surfaces. Let the foam act for up to 30 min- head utes for the optimal effect.
-
Page 10: After Using The Cleaner
6 After using the cleaner Switching off the cleaner 1. Turn the burner switch to "OFF" position. 2. Activate spray handle for 1 minute minimum on cold water to cool down system. 3. Turn "OFF" engine. 4. Close water tap. 5. -
Page 11: Maintenance
7 Maintenance Maintenance Schedule Every six months or After the first 50 Weekly 500 operating required operating hours hours 7.2.1 Water fi lters 7.2.2 Oil fi lter 7.2.3 Checking the pump oil quality 7.2.4 Changing the pump oil ... -
Page 12: Troubleshooting
8 Troubleshooting 8.1 Other Faults Fault Cause Remedy Engine not started Start engine. > • Engine RPM too low Adjust RPM on the speed > control to max. Cold water operation possible. Pressure too low Replace nozzle High pressure nozzle worn •... -
Page 13: Warranty
ONE YEAR PARTS & LABOR WARRANTY: Manufacturer rescission of the contract of sale of any Magnum product. promises to repair Magnum branded pressure washers if Manufacturer reserves the right to change or improve the... - Page 14 HOW TO OBTAIN WARRANTY SERVICE: replacement date for that part. If the part fails before the first 1. Contact your local service dealer and return the Magnum scheduled replacement, the part will be repaired or replaced washer or part within the warranty period along with your by Magnum according to subsection (4) below.
Need help?
Do you have a question about the 5012MAG-42VM and is the answer not in the manual?
Questions and answers