Miles Industries Valor Retrofire RF24JBN Installation & Owner's Manual

Gravity vent fireplace insert

Advertisement

Quick Links

INSTALLATION & OWNER'S MANUAL
Gravity Vent Fireplace Insert
RF24JBN (natural gas) & RF24JBP (propane gas)
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
▪ If you cannot reach your gas supplier,
call the fi re department.
— Installation and service must be
performed by a qualifi ed installer,
service agency or the gas supplier.
4006515-02
© 2018 Miles Industries Ltd. All rights reserved.
Retrofi re
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Please read this manual
BEFORE
operating this appliance.
INSTALLER
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
This appliance may be installed in an after-
market permanently located, manufactured
(mobile) home where not prohibited by local
codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in
a bedroom or bed sitting room.
Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State of
Massachusetts.
Ce guide est disponible en français sur demande.
US Patent no. 8,166,965
installing and

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Valor Retrofire RF24JBN and is the answer not in the manual?

Questions and answers

Summary of Contents for Miles Industries Valor Retrofire RF24JBN

  • Page 1 fi re department. Ce guide est disponible en français sur demande. — Installation and service must be performed by a qualifi ed installer, service agency or the gas supplier. 4006515-02 © 2018 Miles Industries Ltd. All rights reserved.
  • Page 2: Table Of Contents

    Spare Parts............35 The information contained in this installation manual is believed to be correct at the time of printing. Miles Industries Ltd. reserves the right to change or modify any information or speci- fi cations without notice. Miles Industries Ltd.
  • Page 3: Safety And Your Fireplace

    Safety and Your Fireplace SAFETY AND YOUR FIREPLACE Read and understand all instructions carefully before Do not use this heater as a temporary source of starting the installation. Failure to follow these instal- heat during construction. lation instructions may result in possible fi re hazard and Due to the high temperature, the appliance should be will void the warranty.
  • Page 4 Safety and Your Fireplace Read and carefully follow all safety warnings and operating instructions contained in your owner’s manual Replacement manuals are available by contacting the Valor Service Department at 1-800-468-2567 or visit www.valorfi replaces.com. FOLLOW THESE IMPORTANT CHILD SAFETY PRECAUTIONS AND RECOMMENDATIONS Parts of your Valor Fireplace become extremely hot while in operation.
  • Page 5 SAFETY AND YOUR FIREPLACE This manual and particularly the preceeding and following pages contain very important information regarding the safe operation of your fi replace as well as maintenance instructions. Read carefully before operating your fi replace and pay special attention to the safety warnings. A heating gas appliance does require safe handling.
  • Page 6: Introduction

    INFORMATION Thank You ... Operating Your Fireplace for the First Time For purchasing a Valor by Miles Industries. Your new When operating your new fi replace for the fi rst time, radiant gas heater is a technical appliance that must some vapors may be released due to the burning of be installed by a qualifi...
  • Page 7: Operating Your Fireplace

    1. Set the Flame Adjustment Knob clockwise as far  Should the safety switch require replacement, only as possible. use parts supplied by Miles Industries. 2. Push in the Gas Control Knob slightly and turn it clockwise  to OFF. Do not force.
  • Page 8: Using The Remote Control

    OWNER’S Using the Remote Control INFORMATION BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and automatic ON/OFF can only be programmed when the function display is fl ashing. Be patient when programming as it can take a few seconds to set.
  • Page 9 OWNER’S Using the Remote Control INFORMATION Setting the temperature.)
  • Page 10: Kits & Accessories

    OWNER’S Kits & Accessories INFORMATION Required Accessories Optional Accessories Information accurate at the time of printing and subject Information accurate at the time of printing and subject to change without notice. to change without notice. 4006519 Barrier Screen Decorative Cast Iron Frets Fuel Beds (choose one) RA24FK Fret Kit, required for all frets...
  • Page 11: Lighting Instructions

    OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
  • Page 12: Servicing & Maintenance

    OWNER’S Servicing & Maintenance INFORMATION Servicing Your Fireplace We recommend having your fi replace serviced every year. Contact your supplier quoting the model number. It will be helpful if the appliance’s serial number can also be quoted. These numbers are on the information card.
  • Page 13: Cleaning Your Fireplace

    Remove the window to clean the fi replace. only and are not meant to guarantee results. 1. Bottom cover: If using a bottom cover, pull it out to NOTE: This is a problem beyond Miles Industries’ unhook it. control and is not covered under warranty.
  • Page 14 QUALIFIED Servicing & Maintenance INSTALLER 3. Glass window: Rotate the four fastening studs at Reinstall the barrier screen and window frame. the bottom corners and sides 90 degrees to release WARNING them. Unhook the glass window. F O R S A F E T Y P U R P O S E , ensure the barrier screen is re-installed on the fi...
  • Page 15: Checking Pilot And Burner Flames

    QUALIFIED Servicing & Maintenance INSTALLER Checking Pilot and Burner Flames The appliance area must always be kept clear and free from combustible materials, gasoline and other A periodic check of the pilot and burner fl ames should fl ammable vapors and liquids. Inspect the vent terminal be made.
  • Page 16: Replacing Batteries

    QUALIFIED Servicing & Maintenance INSTALLER Replacing Batteries 2. The receiver is located to the left of the valve and it is retained to the fi rebox by a Velcro tab. Grab the WARNING receiver and pull it out from its location. DO NOT ATTEMPT TO CHANGE THE BATTER- IES WHILE THE FIREPLACE IS STILL HOT! Let the fi...
  • Page 17: Specifi Cations

    QUALIFIED Specifi cations INSTALLER *High Altitude Installations This appliance is intended for installation into existing masonry or factory-built, solid-fuel burning Input ratings are shown in BTU per hour and are fi replaces only. certifi ed without deration for elevations up to 4,500 feet (1,370 m) above sea level.
  • Page 18: Dimensions

    QUALIFIED Dimensions INSTALLER Dimensions— for Solid-Fuel Burning Fireplace Insert Only See separate framing Dimensions for Zero Clearance applications with the Zero Clearance Kit RA24ZC. 26-1/2” 24-1/2” 24-3/8” 17” 8” 7-5/8” Stand-offs 1225VFB Ventana Fret (Black) RA24TB Fret (Black) 3” dia. 25-1/2”...
  • Page 19: Vent Confi Gurations

    QUALIFIED Dimensions INSTALLER Mantel / Hearth Clearances Combustible Mantel and Hearth Clearances for insert NOTE: The glass front and hearth are very hot. Existing applications must conform to those required for the wire mesh screens or free standing hearth mounted original solid-fuel burning fi...
  • Page 20: Existing Fireplace Preparation

    QUALIFIED Existing Fireplace Preparation INSTALLER Gas Line Routing A few points must be considered before inserting the RF24 into an existing fi replace cavity. Generally, Plan the routing of the gas line before proceeding. modifi cations to the existing fi replace that will compro- Utilize the existing hole for the gas line.
  • Page 21: Installation

    QUALIFIED Installation INSTALLER Connect Gas Supply • Make sure that the appliance is turned off . • Open the manual shut-off valve. • It’s preferable to rough-in the gas line at this point • Test for leaks by applying a liquid detergent before proceeding with the fi...
  • Page 22: Rough-In Vent Liner

    QUALIFIED Installation INSTALLER Rough-in Vent Liner Prepare Appliance Rough-in the 3” diameter vent liner into existing The size of the existing fi replace cavity will aff ect the chimney system being careful not to tear or damage method of installation. Smaller fi replaces, particularly the liner in the process.
  • Page 23: Connect Vent Liner To Appliance

    QUALIFIED Installation INSTALLER Connect Vent LIner to Appliance Re-install Support Legs (if removed) The vent plate will ultimately locate approximately 19” With the fi rebox recessed behind the smoke curtain above the base of the fi replace once inserted. of the existing fi replace, raise the fi rebox and place the individual support legs under the fi...
  • Page 24: Level Appliance In Hearth

    QUALIFIED Installation INSTALLER Level Appliance in Hearth Note: The upper baffl e may be removed to gain more room for the screwdriver to install the rear screws. The backside of each support leg has a leveling bolt. If necessary, adjust the level of the fi rebox in the hearth. Remove top baffl...
  • Page 25: Install Top Convection Baffl E And Extension

    QUALIFIED Installation INSTALLER Install Top Convection Baffl e and Extension 3. Slide the extension, channels downward, over the edge of the convection baffl e. Keep the extension Position the fi rebox as far back as possible within the baffl e as far forward as possible, angled down if existing fi...
  • Page 26: Install Traditional Log Set Mf28Lsk

    QUALIFIED Installation INSTALLER Install Traditional Log Set MF28LSK 3. Place the top left log on the pin of the rear log. The bottom of the log rests on the left side end of the Material required front left log just installed. •...
  • Page 27 QUALIFIED Installation INSTALLER 4. Place the front right log on the burner and slide it to 6. Place the lower end of the center right log onto the the left against the front left log. pin on the front right log. Rest the narrow end in the notch into the rear log.
  • Page 28: Install Driftwood Set Mf28Dwk

    QUALIFIED Installation INSTALLER Install Driftwood Set MF28DWK 2. Identify the rear log and place it on top of the base log locating it into the notches on top of the log. Pull Material required the log forward so it is locked in position. •...
  • Page 29 QUALIFIED Installation INSTALLER 4. Identify the left side cross log which has one pin at one end. Insert the pin in the hole at the front left of the platform and rests the top part of the log into the notch of the rear log as indicated.
  • Page 30: Refi T Window

    QUALIFIED Installation INSTALLER Refi t Window 2. If the Hot Glass Warning plate has been removed from the front lower corner of the window, 1. Hook the glass window to the fi rebox then fasten the reinstall it by sliding it between the glass and four studs pushing and turning them 90 degrees.
  • Page 31: Check Operation

    QUALIFIED Installation INSTALLER Check Operation Depending of fuel bed used, altitude and other considerations, the fl ame picture may be improved by Turn the fi replace fl ame up and down using the adjusting the aeration. The need for adjustment should remote control to confi...
  • Page 32: Install Barrier Screen To Window Cover

    QUALIFIED Installation INSTALLER Install Barrier Screen to Window Cover Install Top Vent Shield (if necessary) A barrier screen is supplied with this appliance to install The top vent shield is designed to install on top of the on the Retrofi re window cover. The barrier screen fi...
  • Page 33: Install Bottom Cover Or Cast Iron Fret

    QUALIFIED Installation INSTALLER Install Bottom Cover or Cast Iron Fret Fret Installation Fret Brackets Installation RA24FK Bottom Cover Installation 1. Screw 2 thumbscrews into each retainer tab. Slide the top fl ange of the bottom cover into slots 2. Fit the retainer tabs to each leg (1 screw per side). located at the bottom corners of the window frame.
  • Page 34: Warranty

    1. Extended Warranty Coverage For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the initial owner for the repair of, or will exchange the following parts or components which are found to be defective in material or workmanship...
  • Page 35: Spare Parts

    OWNER’S Spare Parts INFORMATION Description Part No. Description Part No. Firebox Assembly 4006517AH Pilot Mount 4000138 Vent Plate Assembly 4001010 Pipe—Valve to Main Burner (incl. 4000065 olive & nuts) Vent Shield 4006428BY Valve Tray 4006034 Vent Switch Assy 4000204 Break-off Olive Nut—Pilot Pipe to Vent Switch Bracket 4001008 220K913...
  • Page 36 OWNER’S Spare Parts INFORMATION Spare Parts MF28LSK RA24FK Natural gas Propane gas MF28DWK...
  • Page 37 Serial Number: Date Purchase (yyyy-mm-dd): Dealer: Customer Information First Name: Last Name: Contact Information Email: Mailing Address Address: City: Province/State: Postal/Zip Code: Country: Cut out page, fi ll information, and mail to Miles Industries Ltd. Online Warranty registration at www.valorfi replaces.com...
  • Page 38 Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...

This manual is also suitable for:

Valor retrofire rf24jbp

Table of Contents