Related Manuals for Z-Com LANEscape WH2330
Summary of Contents for Z-Com LANEscape WH2330
- Page 1 PCMCIA Adapter...
- Page 2 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital devices pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication.
- Page 3 Limited Warranty In no event will Z-Com be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure or interruption of Z-Com’s products, whatever...
-
Page 4: Table Of Contents
Contents Chapter 1 Windows 95 Set-up and Configuration ......5 1-1 Installing the WH2330 Windows 95 Network Driver ............5 1.2 Re-installing / Upgrading the WaveRider-II network drivers........... 6 1.3 Operational / Optional Characteristics of the WH2330 ............ 8 Chapter 2 Using the WH2330 Upgrade Utility ........ -
Page 5: Chapter 1 Windows 95 Set-Up And Configuration
Chapter 1 Windows 95 Set-up and Configuration 1-1 Installing the WH2330 Windows 95 Network Driver The WH2330 (Mitel Semiconductor WaveRider-II) network adapter is a plug and play adapter. If the driver is being installed for the first time, then the installation is simple and straightforward. If the WH2330 is being upgraded or re-installed then pleaase see Section 1.2. -
Page 6: Re-Installing / Upgrading The Waverider-Ii Network Drivers
Click on the “OK” button and the drivers will be installed for the WH2330. If the PCMCIA slots have the sound enabled, then a low-high tone sequence should be heard. The WH2330 will be configured for operation as a Slave unit by default. If you have a Master station running, then the network should be available to you. - Page 7 From the control panel select Network. From the Network control panel, select the Mitel Semiconductor WaveRider-II adapter. Be careful to select the correct adapter and make sure that the picture of an adapter is next to the description of the adapter, as shown below:...
-
Page 8: Operational / Optional Characteristics Of The Wh2330
Click on the “Remove” button. If you have hardware profiles installed, you will be asked if you want to remove all occurrences of the adapter, as shown below. Click on the “OK” button to uninstall the driver. Finally click on “OK” in the Network set-up Panel. The driver for the WH2330 will then be removed. - Page 9 From the Control Panel select Network. From the Network, select the Mitel Semiconductor WaveRider-II adapter. Be careful to select the correct adapter and make sure that the picture of an adapter is next to the description of the adapter, as shown below.
- Page 10 Click on the Properties button to display the properties of the adapter. Click on the Advanced Tab at the top of the panel to display the advanced settings for the adapter. The Advanced settings for the adapter can now be configured for your network. Software...
-
Page 11: Chapter 2 Using The Wh2330 Upgrade Utility
Chapter 2 Using the WH2330 Upgrade Utility The WH2330 upgrade utility (upgrade.exe) is a Windows application which allows users to upgrade the Media Access Control (MAC) software held in the WH2330 adapter. We may, from time to time, issue new versions of the MAC software in order to add new functions or correct problems. -
Page 12: Appendix Wh2330 Specifications
Appendix WH2330 Specifications Interface PCMCIA Over 150 meters line of sight / 50 meters in an Range office environment Receiver Sensitivity Typically –83dBm Tx/Rx/Tx Switching Time Maximum 224us Channel Hopping Time Maximum 224us Data Rate 1 Mbits/sec across air MAC Protocol GPSP CSMA/CA Frequency Band 2.4~2.4835 GHz...