Kenmore 449.31031 Owner's Manual page 5

STEPS TO INSTALL YOUR WATER HEATER (Continued)
COLD WATER
HOT WATER
Shut-off
Valve
Vacuum Relief
Valve (Included)
_-/ o
Flexible 3/4" ...m _1 _ 3/4" 90.,
Installation Nipple kd _ /_[ree_ _loow
Tube r_,1_ .
3/4. tl jV_.L_.p Cold Side
Female I_Jl_ HeatTrap
• Hot Side "---_!_ Tee L_
Heat Trap I-1 _'
L.J ( "_ _=_ 1" x 3/4" Reducer
L2 Bush og I,oduded)
Seal Ring
(Included) / /'-" "_ "_" Seal Ring
t / / xx ] (Included)
Outlet (HOT) Hex Inlet (COLD) Hex
Union Nut Union Nut
WATER HEATER
INSTALLATION KIT
HOT
WATER _
90° Elbow ,/_ I
3/4"
Female Tee
OR
Vacuum Relief
Valve (Included)
_r-_ COLD
WATER
S_hut-off
Valve
Flexible _j,.q , .
Installation-'---! Cold Side
Tube \ Heat Trap
Hot Side "_ //
Heat Trap _ _1
"_1 _ _ l" x 3/4" Reducer
Seal Ring LJ _ {_p./"- Bushing (included)
(Included) "--.._ea _._ ,_
)_ _eal Hing
[/ -'_-- -- --._,,'_(Inclu dad)
Outlet (HOT) Hex Inlet (COLD) Hex
Union Nut Union Nat
Vacuum Relief
Valve (Included)
_[_ COLD
WATER
/
Shut-off
Valve
*Gold Side
Heat Trap
{_-,_" I" x 3/4" Reducer
Bushing (Included)
Seal Ring
(Inc]uded)
Outlet (HOT) Hex Inlet (COLD) Hex Outlet (HOT) Hex
Union Nut Union Nut Union Nut
Inlet (COLD) Hex
Union Nut
COLD WATER
HOT WATER _ Shut-off
1 -
/ / _ _, Vacuum Relief
Union (2) --t:-:_ _ I_--" Valve (Inc uded)
3/4" Female _"-'= Fe3/L:le 'FI_' '_ o
Coupling _] Tee r_ _"_ _--_. 3/4[ "gO'
. '"UP ,ree, ,oow
*Hot Side _r_ _.,,._, *Cold Side Heat Trap
Heat Trap \k,..J tl
_',_ _ t_ _ 1" x 3/4" Reducer
Seal Ring . _ is _ !_ Bushing (Included)
(Includ_ Seal Ring
_/F ,_ k_ (Included)
Outlet (HOT) Hex Inlet (COLD) Hex
Union Nut Union Nut
THREADED PIPE
vacuum Relief
Valve (Included) _
HOT WATER _ ^,,f _ COLD
/- I_ F_rnale _ WATER
90 ° Elbow _.& Tee Shut-off
Union (2) """ v[: l'''''' ' Valve
3/4" Female. U _
/
"Cold Side
OR
Coupling (2)"',r_ _/- Heat Trap
• "_. "_ _ 1" x 3/4" Reducer
*Hot Side "_=_ _ _ .,. Bushing (Included)
.eat.rap _ (3 _"
Seal Rin _ N Seal _;_
(,ncluded)K_--
v
_-_/_ (Included)
Outlet (HOT) Hex Inlet (COLD) Hex
Union Nut Union Nut
NOTE: The inlet fitting on electric water heaters is a 1-inch inside threaded hex union. Unions (dotted lines) are not needed if
the inlet and outlet pipes move enough to allow connection Dr if flexible supply lines are used:
* SEE PAGE 13 FOR HOTAND COLD HEAT TRAP INSTALLATION DETAILS.
5