Advertisement
Using a LRR-4 with an ES-1 or ES-3 for Wireless Gate Control
A basic gate access controlled entry point is wired
as shown right. The relay can be connected as
either Normally Open, or Normally Closed. All 26
bit Wiegand devices are fully supported.
Power and Data from the ES-1 (Data only
from ES-3) can be installed up to 500 feet
away using 24 gauge wire. Viking Wiegand
devices can run even further. The ES-1 or
ES-3 can support either a LRR-4 Receiver or
Proximity Card Reader (Viking model PRX-1
or PRX-3), or both. If any two Wiegand
devices are used, one can be placed on each
side of a doorway/gate for bi-directional
(entry and exit) access control.
Using a LRR-4 with a C-4000 to Wirelessly Control up to 4 Gates
For more information see Viking C-4000, Apartment / Office Entry Controller, Product Manual DOD 164.
Issue / Possible Causes
No data received / Transmitter not enrolled
Short Read Range / Receiver Knob
Prox insert not working / Compatibility
Should any of the corrective actions mentioned above not improve performance, please contact Viking directly.
Note 1. This lithium battery is widely available, and commonly used in electronic devices, including cameras and remote controls.
Note 2. Dispose of the battery according to local requirements. Recycle when possible.
Note 3. For best performance the Transmitter should be used as far from interference sources as possible. These sources may include, but are not limited to, large metal
obstructions, such as duct work and appliances, as well as magnetic fields and radio emissions.
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Product Support Department is available for assistance Monday - Friday 8am - 5pm central time. So we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)
number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually
boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address in the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of two years from the date of purchase from any authorized Viking distributor. If at any time during the warranty period,
the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization
(R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover non-
EWP products that have been exposed to wet or corrosive environments. This warranty does not cover stainless steel surfaces that have not been properly maintained.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES
ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL BE
LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLUSIVE
REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED AS SUCH.
12V DC Adapter
(included with ES-1)
120V AC
Gate
Remote Touch
RAD-1A Remote Access
Tone Programming
Device (not included,
Phone (not included)
see DOD 410)
Troubleshooting
Correction Action
Transmitter must be clicked twice to be learned by the Receiver upon initial Receiver power up
Adjustable knob should be set to the maximum setting
Support with HID® 125-kHz Proximity Protocol readers only
Warranty
TWO YEAR LIMITED WARRANTY
3
VIKING
MODEL ES-1
©
VIKING
ELECTRONICS
HUDSON, WI 54016
STAND ALONE
DOOR CONTROLLER
ENTRY SYSTEM
1
2 3 4 5 6 7
OR
Touch Tone
Programming
Phone (not included)
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking's Technical Support at 715-386-8666 to determine possible causes for the problem.
The customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the Viking product using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
Viking ES-1
(not included, DOD 193)
Viking ES-3*
(not included, DOD 195)
* Important: When using the LRR-4 with
an ES-3, the LRR-4 must be powered
separately by a 12 VDC power adapter
(Viking model PS-2A).
+VDC is connected to "+" on PWR
adapter. GND is connected to "-" on PWR
adapter and to "BLK" terminal on ES-3.
8 9 10 11
Model
LRR-4
Optional Viking PRX-3
(not included, DOD 221)
12V DC Adapter
(included with PRX-3)
120V AC
or
Advertisement
