Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BECS BECSys7 230VAC
Summary of Contents for BECS BECSys7 230VAC
- Page 1 Operation and Maintenance Manual...
-
Page 3: Table Of Contents
A – 5.11: Filter Backwash ........17 Section H: Warranty ............. 37 A – 5.12: Sensor Wash ........18 A – 5.13: Enzyme ..........19 A – 5.14: Polymer ..........19 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 5: Warnings
This manual was written for firmware v2.20. If you received newer firmware but did not receive a copy of the manual covering that version of firmware, please contact your distributor. Page 1 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 6: Environmental Conditions
250VAC/30VDC (max) – 3 Amps Relay 8 (K8) 250VAC/30VDC (max) – 3 Amps 250VAC/30VDC (max) – 3 Amps Relay 9 (K9) 250VAC/30VDC (max) – 3 Amps 250VAC/30VDC (max) – 3 Amps Page 2 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 7: Nsf Suggested Operation Ranges
Pressure Swichgage 0 – 50 PSI Differential Swichgage 0 – 50 PSI Conductivity Sensor 0 – 20,000 micromho Turbidimeter 0 – 20.0 NTU Flowmeter 0 – 655.35 Kgpm Page 3 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 8: Section A: Programming The Controller
"Bad Value, Retry..." - Accompanied by an error beep, this indicates the value you just entered was not within the allowable range of values and was not stored. Page 4 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 9: A - 3.2: The Menu Screens
For some values, certain keys may take on special functions that are explained in the lower lines of the screen. The Down/up message in the example above is one of them. Page 5 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 10: A - 3.3: The Lock Screen Key
You can also select cancel if high alarm or fall below the low alarm before the you pressed the lock button in error. alarm will shut off. Page 6 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 11: A - 4.3: Cl Inputs Setup
The value entered must be 1.0 ppm or greater. Diagnostics (Op): This option displays input diagnostic values. Reset Calibration (Op): Resets the calibration to the original factory setting. Page 7 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 12: A - 4.3.2: Total Cl Setup
Alarm Hysteresis (Mgr): This value sets at what level the inventory level or weight has to rise above the low level or weight alarm setting before the alarm will shut off. Page 8 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 13: A - 4.9: Turbidity
Display Input (Op): This option alarm before the alarm will shut off. enables/disables displaying the Pump Effluent pressure on the normal display. Page 9 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 14: A - 4.11.5: Strainer Vacuum
You may disable this alarm by holding down the +/- key for 1 second. Page 10 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 15: A - 5: Control Outputs
During this time, the feeder will turn on for a percentage of the Time Base and turn off for the remainder. Page 11 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 16: A - 5.2: Chlorine Control
If in TBP Pause mode, the if using calculated ppm control. This value sets the controller will reset the timer. desired level to maintain the ORP at. Page 12 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... - Page 17 AM/PM, press the +/- key while the cursor is on the time you wish to change. Page 13 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com...
-
Page 18: A - 5.3: Chlorine Booster Control
(the range is 0:00 to 18:00 hours) The most common failures of automated chemical feed systems are depletion of the chemical supply and/or chemical feeder failure. Both problems result in the controller Page 14 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 19: A - 5.5: Dechlorination
18:00 hours) ORP Set Point (Op): This option is only shown if the Control Input is set to ORP. This value sets the desired final ORP level. Page 15 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 20: A - 5.7: Heater
Heater Primary: Operate the heater only during regular hours and the chiller only during Page 16 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 21: A - 5.10: Bleed Valve
The 4 Event 28 Day above the Set Point before it triggers a Timer allows you to program a backwash backwash. based on a schedule. Page 17 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 22: A - 5.12: Sensor Wash
(except manual start) from starting a backwash is between the active event's start and end times. if triggered within this time period from the end Page 18 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 23: A - 5.13: Enzyme
100%, the triggering of the Out Of Range (OOR) alarm will be delayed by this amount of time. Set to 0 to disable the alarm. Page 19 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 24: A - 5.16.1.1: Scheduled Turndowns
Only once the flow rate is above the minimum flow rate for that equipment will that control be allowed to run. Page 20 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 25: A - 6: Control Options
GOING TO SLEEP again once all equipment or harm patrons. feeds have been satisfied again. While Power Saver is active, the system automatically uses the Alternate Temperature Page 21 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 26: A - 7: Calculations
SMTP server manually via the remaining items listed here. (SSL, TLS, or none). SSL and TLS are usually used in combination with Authentication. Page 22 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 27: A - 8.2.4: Call Out Setup
Test: Triggers a test call-out of the current recipient only. You may only test one Page 23 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 28: A - 8.5: Display Options
Inputs: Lists all enabled inputs compatible for outputting on the selected 4-20mA output channel. Feed Set Points: Lists all enabled controls using feed set points. Note that some feeds Page 24 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 29: Section B: The Normal Display
If there are any active alarms while one or more of these control functions' are active, the alarms will be shown every Page 25 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 30: Section C: Using The Face Panel Quick Keys
If you have the controller set up to control a VFD or value. if any 4-20mA recorder outs have been assigned, Manual Flow Rate changes the VFD output to maintain a specified flow rate. Page 26 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 31: C - 3: The Cal Key (Calibration)
During a backwash, the Backwash Key displays the progress of each filter and allows you to restart, switch to, or cancel a particular filter as well as cancel the backwash entirely. Page 27 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 32: C - 5: The Reset Fail / Safe Key
All the other relays will remain off until the emergency off button is press again. Page 28 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 33: Section D: Becsys For Windows
All Programs BECSys for Windows group. This will walk you through the steps to create a site. Page 29 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 34: Section E: Maintenance
After removing the sensor from inside. Tighten slowly to the stop. from the flow cell, clean it as in routine Page 30 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 35: E - 3: Free Chlorine Sensor (Cp-1)
Add a new set of replacement glass beads membrane cap. when the sensor is put back into service (BECS part number 2210444). Warning: Never touch the electrode finger. Fill the membrane cap to the edge with the E –... -
Page 36: E - 4: Conductivity Sensor
Use the Probe Nut to secure the sensor inside the Flow Cell. The top of the Probe Nut should be at the bottom of the label. Page 32 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 37: Section F: Feed Charts
1.25 ts 0.100 ts 0.167 ts 0.250 ts 0.50 ts 0.75 ts 1.00 ts ts = teaspoon tb = tablespoon cp = one cup (8 fl oz) Page 33 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... -
Page 38: F - 2: Pool Feed Charts
= one cup (8 fl oz) pt = one pt (16 fl oz) qt = one quart (32 fl oz) gl = one gallon (128 fl oz) lb =pounds of dry chemical Page 34 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132... -
Page 39: Section G: Replacement / Maintenance Parts
Flowmeter (10” to 36”) [range: 0 to 655.35 Kgpm] Documentation 8620108 BECSys7 Operation and Maintenance Manual 8620111 BECSys7 Installation and Technical Manual 8620038 BECSys7 Laminated Quick Reference Sheet Page 35 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com... - Page 40 Operation and Maintenance Manual Rev: C17 Page 36 www.becs.com 9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132...
-
Page 41: Section H: Warranty
BECS will repair, or if repair is not possible, replace the defective part or parts of the BECSys controller. BECS will have the sole right to determine whether to repair or replace a product. BECS will not be responsible for any expense associated with installation of repaired or replacement parts. - Page 42 Louis, Missouri is home to an exceptional design team, and all manufacturing is performed onsite at this facility where we can personally assure the quality of our products. The BECS commitment to excellence drives the most innovative new products and unparalleled customer service.
Need help?
Do you have a question about the BECSys7 230VAC and is the answer not in the manual?
Questions and answers
Is there suppose to be water in the place where the two sensors are?
Yes, there is supposed to be water where the two sensors are located in the BECS BECSys7 230VAC. The sensors are installed inside the Flow Cell, which is designed to be filled with water for proper sensor operation.
This answer is automatically generated