Bircher Swissdoor InTra6 3 Translation Of The Original Instructions

InTra6 3, InTra6
Translation of the original instructions
Safety and warning notices
The electrical connection may only be set up by an electrician. The arrangement of the components depends on the structural conditions and
the gate design. Switch off the operating voltage before working on the system. The switching device monitors pressure-sensitive protective
devices from Bircher Reglomat AG (proper use). Use of components not supplied by Bircher-Reglomat (including safety edges) will render the
guarantee and liability null and void. Connect all operating and switching voltages to the same fuse. Connect the operating voltage to the
same circuit as the industrial door controller. Disconnect device from mains in the event of a fault. Protection max. 10 A
1 System components
1
Close
5
1
Close
5
2 Electrical connection and terminal diagram
Operating
Version
voltage
InTra6 3
+/~
InTra6 3.LVAC –/~
* The outputs are monitored need to be connected, otherwise an error code is displayed (E007)!
3 Operation
«Mode» button
Control buttons
Mode
on device:
4 Standard operation
When everything is connected correctly:
Display after switching on:
Status LED lights up green
5 Diagnostic menu
« » «
Press the Mode and Data
« »
Press the Mode button for 2 s to exit diagnostic menu.
Error display mode
The 5 most recent errors
can be interrogated.
« »
Press the Data key briefly in
each case, and the errors are dis-
played one after the other. End
« »
appears when the Data button
is pressed for the 5th time. The
malfunctions are displayed in
chronological order (new old)
Mode «S» Both outputs
1 2
– Both outputs deactivated
– No current flow OK
1 2
– At least 1 output with current flow Error
– Press the «Data» button
1 2
– Both outputs are activated
– Current flow OK
– At least 1 output without current flow
1 2
Consumer missing
3.LVAC
4
3
Open
9
7
4
3
2 2
9 6
7
Stationary safety
edge CLOSE
A1
A2
Display
«Data» button
1
Data
Displays shown when safety edge is actuated: Status LED lights up orange
actuated:
Dots
flash
»
buttons simultaneously for 2 s status LED flashes orange. Press
Mode «r» Resistance
The resistances of the
safety edges are displayed
Example:
8 = Resistance between
7 and 9 kohm.
1 = safety edge
To access the next safety edge:
« »
Press the Data button
Mode «C» current configuration
Switching device with inductive transmission system used in combination with safety
edges to avoid dangers at crushing and shearing points in sliding gate systems.
Mobile safety edge CLOSE
(primary closing edge)
Mobile safety edge OPEN
Stationary safety edge CLOSE
Stationary safety edge OPEN
INTR-MOB61, converter for
safety edge
Open
Hole
grey
Stationary safety edge
OPEN
1
3
2
4
CLOSE Output
OPEN Output
2
Mode
Data
Dots
actuated:
1
Mode «S» Output CLOSE
1
– CLOSE output is deactivated
– No current flow OK
– Current flow error
1
– Press the «Data» button
1
– CLOSE output is activated
– Current flow OK
– No current flow Error
1
(consumer missing)
Displays current configuration of
safety edge inputs, see configura-
tion table.
Configuration chapter 6
INTR-MOB62, converter for
mobile safety edge
INTR-FIX60, coil
InTra6 3, switching device
Steel cable (see chapter 9.3)
Hole
red
Coil
Output
connection CLOSE*
YE
RX
GN
14
WH
11
TX
BN
= Symbol for display flashes
actuated:
2 1
« »
Mode buttons briefly to change to the next mode.
Mode «S» Output OPEN
2
– OPEN output is deactivated
– No current flow OK
– Current flow error
2
– Press the «Data» button
2
– OPEN output is activated
– Current flow OK
– No current flow Error
2
(consumer missing)
Mode «h» current fall-delay time
Displays current fall-delay time,
see fall-delay time table.
Configuration chapter 6
To access the configuration mode:
Press the «Mode» button
255838W
08/13
Output
OPEN*
24
21
actuated:
2