Subscribe to Our Youtube Channel
Related Manuals for Silvey RAZUR SHARP II
Summary of Contents for Silvey RAZUR SHARP II
- Page 1 RAZUR SHARP II THE ‘R2’ SQUARE CHISEL CHAIN GRINDER OWNERS MANUAL MANUFACTURED BY: 4007 CRATER LAKE HIGHWAY MEDFORD, OR 97504 Phone: 541-734-4118 Fax: 541-734-2324 E-mail: info@silveychaingrinder.com www.silveychaingrinder.com...
-
Page 2: Table Of Contents
Why to save R2 box, how to assemble the stand Basic Instructions............... Page 4 Step by step, guide for sharpening your square chisel saw chain ® with the Razur Sharp II for the first time. Read completely before using this grinder. Sharpening For the First Time..........Page 6 Maintenance and Tips............Page 7... -
Page 3: Razur Sharp Ii
If you purchased and picked up your Razur Sharp II grinder from a shop, your grinder is ® probably assembled and mounted on the stand. If you ordered your Razur Sharp II and had it sent to you, this section will be helpful. -
Page 4: Basic Instructions
- Basic Operating Instructions RAZUR SHARP II ® 1) Check to be sure that nothing is touching the grinding wheel. Retract the wheel dressers and move anything else that may come in contact with the wheel. Locate the large handle lever on the bottom front of the grinder. - Page 5 Basic Operating Instructions RAZUR SHARP II ® WARNING: Dressing out large amounts of wheel material in one pass may cause the wheel to chip or break while it is spinning. This could injure you and damage your grinder. Always dress away from the working corner of the wheel.
-
Page 6: Sharpening For The First Time
- Sharpening for the First time RAZUR SHARP II ® 11) Grinding INTO the tooth will NOT splinter the chrome allowing the tooth to stay sharper longer. The chrome is the hardest part of the tooth, if it is splintered, it will not hold an edge very long. Which is the ®... -
Page 7: Maintenance And Tips
The Silvey SNO21-H wheel has been specifically formulated to the optimum specifications of grit, bond ® and motor RPM for Silvey grinders. The grinding wheel can be reached by removing the wheel cover which is held in place by two screws. Be sure to replace the arbor nut, flange washer and wheel cover before operating the grinder again. -
Page 8: Compensating For Wheel Wear
- Maintenance& Tips RAZUR SHARP II ® Compensating for Wheel Wear Your grinding wheel will gradually become smaller in diameter as you dress the stone with the diamond dresser and sharpen chain. This can be compensated for by sliding the chain carriage assembly closer to the grinding wheel. -
Page 9: Reshaping The Wheel
- Reshaping the grinding wheel RAZUR SHARP II ® The diameter of the grinding wheel and the location on the arch of the wheel where the cutter tooth comes in contact with the grinding surface are also determining factors on the angles ground into the cutter tooth. -
Page 10: Tips On Grinding
Tips on Grinding RAZUR SHARP II ® TIP: Do not overheat the tooth when grinding. You do not need a thermometer to monitor heat, simply watch the surface of the cutter tooth. If the tooth starts to discolor, you are getting it too hot. If you heat a tooth to the point that it turns blue, you have ruined it. -
Page 11: Other Tips On Grinding
OTHER GRINDING TIPS - Dos & Don'ts Do not grind with the corner or the stone high into the tooth; this makes a chain perform very poorly. Do not leave a long and/or tall gullet. • Do not grind into the side straps. •... - Page 12 ~ 12 ~...
-
Page 13: Razur Sharp Ii Parts List
Razur Sharp II Parts List ILLUS# DESCRIPTION PART# ILLUS# DESCRIPTION PART # Serial Number Location Cross Slide Mount 152-R Motor Cross Slide Extrusion 153-R Motor Cord Cross Slide Bar 154-R Arbor Chain Bar Mount 155-R Arbor Flange Chain Bar Mount Screw... -
Page 14: Razur Sharp Ii ® - Stand
~14~...
Need help?
Do you have a question about the RAZUR SHARP II and is the answer not in the manual?
Questions and answers