Table of Contents
Advertisement
Battery and Battery charging
Installation
Power on / off
Volume up / down
Redial
Audio-Power-Off
Answer an Incoming call
Put on hold call
Reject an Incoming call
Hang up call
Auto-Answer call
Music Play / Stop
페이지 1 / 11
BiT-1, BiT-2
BiT-1 and BiT-2 are functionally equivalent!
Contents
Advertisement
Table of Contents
Summary of Contents for UNIMO Technology ChatterBox BiT-1
-
Page 1: Table Of Contents
BiT-1, BiT-2 BiT-1 and BiT-2 are functionally equivalent! Contents 1. GETTING STARTED Main Feature Unpacking and Inspection Battery and Battery charging Installation 2. GETTING TO KNOW YOUR BiT-1, BiT-2 Buttons and Inputs 3. BASIC FUNCTION Power on / off ... -
Page 2: Getting Started
Technical Data Home page / contact info 1. GETTING STARTED Thank you for choosing our ChatterBox BiT-1, BiT-2, Motorcycle Bluetooth Communication System. (1) Main Feature (BiT-1, BiT-2 are Functionally Equivalent) Bluetooth V 4.1 Advanced Noise Control Usable during Charging... - Page 3 Main Unit with a pre-installed battery USB charging Cable and AC Adaptor Headset with Microphones for Open and Full face helmets. Velcro Speaker Disks, Foam Mic-covers, Microphone Velcro Helmet Mounting Velcro-type-sticker Manual and ChatterBox logo sticker ...
- Page 4 Do not use the product in sub-zero temperature, because it may cause serious reduction of the battery performance. If you apply heat to the battery or throw it into fire, it may explode. Do not use the product with a damaged battery. It may explode and/or cause accidents. ...
-
Page 5: Getting To Know Your Bit-1, Bit-2
BiT-1 Installation by using Glued Mounting plate ① Clean the surface of the helmet where BiT-1 need to be placed by using a clean towel ② Peel off a protective wrap-cover of the Velcro tape ③ Stick the Velcro on the helmet tightly. ④... -
Page 6: Voice Calling
Voice calling : Long press PLUS button(D) for 1.5 seconds Last number dial : Long press MINUS button(E) for 1.5 seconds Automatic power-off : As no-operation is running for 90 minutes, the unit automatically turned off to prevent self-discharge 4. MOBILE PHONE CONNECTION Mobile Pairing : ①... -
Page 7: Put The Current Call On Hold, Answer An Incoming Call
Put the current call on hold, Answer an incoming call : Short press M.F button (C) Hang up the current call, Answer an Incoming call : Double press M.F button (C) Put the current call on hold, Reject an Incoming call : Long press M.F button (C) for 1 second Hang up the call : Long press M.F button (C) for 2.5 seconds MUSIC Enter Music Mode : Short press M.F button(C) - Page 8 void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 9 In order to get this service, the first end-user must be able to provide the purchase receipt with the date of purchase In case of returning via courier, the end-user must be able to return the defective product with its ...
- Page 10 Liabilities Disclaimer In addition to damages which may occur due to the use of the product, Chatterbox will not be liable for damages of the product which occur due to the following events. In the event the product is misused or used for purposes other than its intended purposes. ...
- Page 11 Bluetooth Chip Qualcomm RF Power Class 2 Audio Power 250mW x 2 Operating Voltage 3.7V Current (Talking) 50mA Current (Standby) Antenna Type Strip line Type Installation BiT-1 : Velcro Type BiT-2 : Cradle Type (4) ChatterBox Home page : ChatterBox USA : www.chatterboxusa.com ChatterBox Head office : www.unimo.co.kr...
Need help?
Do you have a question about the ChatterBox BiT-1 and is the answer not in the manual?
Questions and answers