Longzhiyuan Technology LY-101 Manual

Product Overview
Our doorbell is a Wi-Fi enabled Smart Video
Doorbell which helps you to see, hear and speak to
anyone at your door from your smartphone or tablet
from anywhere. This Video Doorbell supports
answering ring calls from mobile App, two-way
audio, instant alert, motion detection and live
monitoring.
Product Features
Battery-powered WIFI video doorbell
Two 18650 specication batteries work regularly
for 8-12 months
LY-101
HD Megapixels collocated with wide-angle lens
Support mobile phone remote fast wakeup within
1 second
2.4G Wi-Fi connection
High quality two-way talk with noise cancellation
Support PIR motion detection, when someone hovers
at the door, it will send push alerts to your mobile phone
immediately
With IR-cut,it can switch automatically and it is
Shenzhen Longzhiyuan Technology Co., Ltd.
clearly visible at both day and night to keep your
home and family safe.
Step 1: Install anchors (on stucco, brick or concrete) Step3: Connect the back patch board to your existing wires .
On stucco, brick or concrete, use the bit to drill two
holes in your wall, and install the anchors.
Step2. Pls unscrew the screws of the back battery
compartment and remove the cover, then install one
or two pcs 18650 battery.
+
18650 Battery
-
! Please install the battery after
identifying the battery polarity. Extra Wires
At the same time, this device support AC8-24V power existing wires
supply and battery charging. If you need external power
supply, please go to step 3.
Product Specication Sheet
Push Notications within
FOV/160°C Wide-angle Notications
Lens
lens (4Glass) 1 second
Device Wakeup
Within 600 ms
6pcs Infrared LEDs with
Infrared LEDs
5 meters ash distance
Working Temperature -20°~ 60° C
PIR Motion Sensor 5 meters PIR distance
Storage Temperature -40°~ 70° C
Storage Up to 32GB Micro SD card
Connectivity 802.11b/g/n Wi-Fi@2.4G
Install your Wobell
Power consumption
A brief introduction of the Wobell.
Battery Two 18650 specication batteries
60 meters (open space without
AC IN
Wi-Fi distance
obstacle)15 meters (indoor)
PIR
Limited distance Reset button
between doorbell 30 meters RESET USB
Camera
and chime indoor
Mic
Video Compression H.264
Battery
compartments
Two-way audio with noise
Voice Intercom screws
cancellation
Call button
Video resolution 1280*720@30 fps
Step 4：Install the back patch board of the doorbell Indoor chime user manual
to the wall using the provided screws.
Volume key Music key
Volume settings
Press the volume key once to trigger one time,
5 levels volume cycles from low to high . In
mute mode, only ashing light when press the
remote control .
Step 5: Mount and screw your device to the back patch Music key
board on the wall (screw on the bottom of the device).
Press once to trigger one time, press for next
music to play once.
Change the ring
The indoor chime has 18 kinds of music for
options. You can press the music key to choose
your favorite music.
Press the volume button for 5 seconds till a
prompt tone "Ding", then turn into learning
mode, press the doorbell button right now, when
the indoor chime made a" Ding ...Ding "prompt
tone, means the relevant music of indoor chime
Screws for double protection
triggered by the doorbell was changed.
Speaker
Terminals
(connect the doorbell power)
Check out all the accessories in the box
1 Screwdriver
5 Anchors 5 Mounting screws
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user's authority to operate the equipment。
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment
and receiver.
—Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV
technician for help
The distance between user and products should be no less than 20cm