Summary of Contents for Kurt 3400V Series
- Page 1 3400V-Series Vise “Manual” Base Assembly 3400V-Forward 3410V- Reverse Operating Instructions Manual ENGLISH...
-
Page 2: Table Of Contents
Table of Contents Introduction .........................3 Installation & Assembly Guide ................4-5 3400V Parts List ......................8 3400V Mechanical Drawing ..................9 Maintenance Schedule ..................8-10 Troubleshooting Tips ..................... 12 Vise Data Use this to fill out information about your vise for quick reference. Purchase Date: _______ - _______- _______ Purchase Order:... -
Page 3: Introduction
Introduction Thank you for purchasing a Kurt vise. The Versatile Lock 3400-Series AngLock vise has a time proven design and the outstanding accuracy of this product is second to none. Backed by a lifetime warranty, this product will last many years when used and maintained properly. -
Page 4: Installation & Assembly Guide
Installation & Assembly Guide Now that you have your new Kurt 3400-Series vise, it’s time to set-up and begin using it. You will see that your new vise comes with a Kurt swivel handle, two chip guards (short & long)supplied in the shipping carton. - Page 5 If you need more clamping force you may need to upgrade to a larger vise. To properly clamp a part in your Kurt vise you should place the part in the center of the jaws resting on the ways of the vise.
- Page 6 ENGLISH | Operating Instructions...
- Page 7 Maintenance Log/Notes: | ENLGISH Maintenance Log/Notes...
-
Page 8: 3400V Parts List
3400V Parts List ITEM# PART# DESCRIPTION 3400V-1 BODY,MACH 3400V-5 SCREW DL430-2 MOVABLE JAW 3400V-3 DL400-111 KURT LOGO TAF PT400-211 BRUSH SEAL 3400V-99 O-RING #117 D40-42 THRUST WASHER D40-41 THRUST BEARING HDHLM4-96 O-RING #125 3400V-8 2-PIECE RETAINING NUT 00-1191 SHCS 8-32 X .375 D40-315 4”... -
Page 9: 3400V Mechanical Drawing
3400V DRAWING | ENLGISH Maintenance Schedule... - Page 10 3410V Parts List ITEM# PART# DESCRIPTION 3400V-1 BODY,MACH 3410V-5 SCREW DL430-2 MOVABLE JAW 3410V-3 DL400-111 KURT LOGO TAF PT400-211 BRUSH SEAL 3600AA-68 O-RING #115 D40-42 THRUST WASHER D40-41 THRUST BEARING HDHLM4-96 O-RING #125 3400V-8 2-PIECE RETAINING NUT 00-1191 SHCS 8-32 X .375 D40-315 4”...
- Page 11 3410V DRAWING | ENLGISH...
-
Page 12: Maintenance Schedule
Maintenance Schedule It is very important to perform regular maintenance on your Kurt vise to assure proper operation. Improper maintenance will result in poor vise performance and may void your war- ranty. Daily/ Weekly 1. Remove chips from surface of vise. - Page 13 6. To re-assemble the movable jaw, apply a “glob” of grease to the under side of the movable jaw in the pocket. Place the spheri- cal segment in the mating pocket and push into the grease. The grease will hold the segment in place when the jaw is turned over to replace.
- Page 14 9.Clean and inspect the counter bore, thrust washers and thrust bearing. 10.Apply water resistant grease to the thrust washer (i.e. Kurt lube p/n KLA or marine grade grease) 11.Install thrust bearing assembly on the screw in the reverse manner.
- Page 15 15.Then turn the collar back TWO (2) more screw holes. This will allow proper distance for the collar to lock on the threads and keep the bearings firmly in place. (Items 15-16—See Fig. 2) 16.Install the four SHCS and tighten. 17.Install the screw support in the body on the screw (Hex end).
-
Page 16: Troubleshooting Tips
Troubleshooting Tips The Kurt 3400-Series vise will operate trouble free for many years, if properly maintained. This product is indestructible. In some cases it will be necessary to troubleshoot. Use the information below to help in the process. Problem: My vise turns hard. - Page 17 Maintenance Log/Notes: | ENLGISH Maintenance Log/Notes...
- Page 18 Maintenance Log/Notes: ENGLISH | Maintenance Log/Notes...
- Page 19 The sole obligation of Kurt Manufacturing Company, Inc. (Kurt) and the purchaser’s SOLE AND EXCLUSIVE REMEDY hereunder, shall be limited to the replacement or repair of any Kurt product or part (by an authorized Kurt technician) which are returned to Kurt Manufacturing Company’s place of business, transportation, shipping and postal charges prepaid, and there determined by Kurt Manufacturing Company to be covered by the warranty contained herein.
- Page 20 Thank you for your purchase! If you have any feedback or questions. Please contact us at: workholding@kurt.com 1-877-226-7823 Like, Tweet, and Subscribe to us! ENGLISH |...